| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| Use after free in Windows Win32 Kernel Subsystem allows an authorized attacker to elevate privileges locally. |
| Use after free in Windows Win32 Kernel Subsystem allows an authorized attacker to elevate privileges locally. |
| Use after free in Windows Kernel allows an authorized attacker to disclose information locally. |
| Use after free in Microsoft Windows Search Component allows an authorized attacker to elevate privileges locally. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: pcm: Serialize PCM mmap with buffer reallocation to fix page UAF
snd_pcm_hw_params() and snd_pcm_hw_free() guard buffer reallocation
with an mmap_count check performed under the PCM stream lock, but the
lock is released long before the buffer is actually freed:
snd_pcm_sync_stop(), constraint refinement and do_free_pages() all
happen in between. snd_pcm_mmap_data(), on the other hand, takes no
lock at all: it validates against the old buffer's state and
dma_bytes, remaps its pages into the VMA, and only then increments
mmap_count.
A concurrent mmap() can therefore slip in between the check and the
free. remap_pfn_range() installs writable PTEs for the old buffer's
pages without taking page references, and the subsequent
do_free_pages() returns those pages to the page allocator while the
VMA still maps them. This leaves a stale, writable mapping of freed
pages: a page-level use-after-free that can be leveraged for local
privilege escalation.
Make snd_pcm_mmap_data() participate in the buffer-access scheme
introduced for hw_params/hw_free: acquire runtime->buffer_accessing
before validating and remapping, and release it afterwards. Buffer
reallocation already fails with -EBUSY while accessors are active,
and the mmap side now fails with -EBUSY while a reallocation is in
progress, so the validate/remap sequence and the check/free sequence
can no longer interleave.
A reproducer that turns this race into a stale writable mapping of
the freed DMA buffer pages is available on request. |
| In the Linux kernel, the following vulnerability has been resolved:
cachefiles: Fix potential UAF/KASAN warning
Currently, trace_cachefiles_coherency() is being passed a pointer to a
__be64 lain over the coherency data in struct cachefiles_xattr so that it
can display the first 8 bytes. However, the data is of variable length and
could even be 0 bytes. This could lead to a UAF or KASAN warning.
Fix this by making sure the buffer has room for at least 8 bytes and that
those 8 bytes are pre-cleared.
Further, those bytes are not 8-byte aligned, so fix the tracepoint to
extract the data as four 2-byte words (they are 2-byte aligned) and
reassemble the __be64. The compiler will convert this into a single 8-byte
load where the CPU supports it. |
| In the Linux kernel, the following vulnerability has been resolved:
unicode: free the map after a grace period
generic_ci_d_hash() and generic_ci_d_compare() read sb->s_encoding and
dereference the unicode map while a pathwalk in rcu mode holds nothing
but rcu_read_lock(). The filesystems that use them, ext4, f2fs and
tmpfs, drop the map with utf8_unload() from ->put_super(), which runs
when the last reference to the mount goes away. A lookup that is still
inside such a filesystem at that point reads a freed map.
With a pathwalk held up in utf8_casefold_hash() while the last reference
to a casefolded tmpfs goes away:
BUG: KASAN: slab-use-after-free in utf8nlookup+0x74c/0x950
Read of size 8 at addr ff110001030fe658 by task walker/98
Call Trace:
<TASK>
utf8nlookup+0x74c/0x950
utf8byte+0x160/0x1560
utf8_casefold_hash+0x167/0x230
generic_ci_d_hash+0xdd/0x1c0
link_path_walk+0x11ad/0x1d30
path_lookupat+0x63/0xb00
filename_lookup+0x1f1/0x5b0
vfs_statx+0xd7/0x3b0
[...]
Allocated by task 94:
__kmalloc_cache_noprof+0x249/0x560
utf8_load+0x4e/0x570
shmem_parse_opt_casefold.isra.0+0x92/0x270
[...]
Freed by task 97:
kfree+0x1db/0x5b0
shmem_put_super+0x72/0x170
generic_shutdown_super+0x14c/0x530
kill_anon_super+0x3a/0x60
deactivate_locked_super+0x9c/0xf0
cleanup_mnt+0x9f/0x130
So far that has been hard to hit. umount(2) waits for a grace period
in namespace_unlock() before it drops the mount, so only a mount whose
last reference goes away elsewhere, like the close of a file or a chdir
out of a lazily unmounted directory, can race a walker. So it is
reachable.
Delay the free until a grace period has passed. The map and the data
table it holds a reference to then outlive any pathwalk that found the
superblock before the mount went away. The reference on the data table
module is dropped from the rcu callback as well. utf8-core is built in
whenever CONFIG_UNICODE is set, so there is no module exit that would
have to wait for the callbacks.
Overlayfs points the s_encoding of an overlay at the map of its first
layer without taking a reference of its own. That stays correct. The
layer is held by the overlay, so its map is dropped only after the
overlay is gone. |
| In the Linux kernel, the following vulnerability has been resolved:
firewire: core: fix race condition in split transaction handling
For a split transaction, either fw_core_handle_response() or
split_transaction_timeout_callback() may manipulate the same transaction
entry in the pending transaction list. The return value of timer_delete()
is used to determine which function handles the entry. If the transaction
is a split transaction and timer_delete() returns zero, the timeout
callback may already be running. In this case, the response handler must
leave the entry in the list for the timeout callback to remove.
A previous code refactoring broke this behavior, introducing a race
condition in which both functions could process the same transaction.
This could lead to a use-after-free on the transaction initiator side.
Fix the regression by ensuring that the response handler does not process
the transaction when timer_delete() returns zero. The timeout callback is
responsible for removing the entry from the pending transaction list. |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: mxc: fix race between chained IRQ handler install and probe completion
mxc_update_irq_chained_handler() is called before the IRQ domain, the
generic IRQ chip, and the port list entry are set up. If an interrupt
arrives in that window:
- mx3_gpio_irq_handler() calls generic_handle_domain_irq() with
port->domain still NULL.
- mx2_gpio_irq_handler() walks mxc_gpio_ports, but the port has not
been added to the list yet.
Additionally, if any of the subsequent probe steps
(gpio_generic_chip_init(), devm_gpiochip_add_data(),
irq_domain_create_legacy(), or mxc_gpio_init_gc()) fail, the error
paths never unregister the chained handler, leaving a dangling handler
that points at freed memory.
Move the handler installation after all its dependencies are ready and
after list_add_tail(), so the handler is never live while the data
structures it touches are incomplete, and is never installed if probe
fails. |
| sharp before 0.35.5 bundles a librsvg dependency affected by a memory-related vulnerability (CVE-2026-96889) that, under certain runtime-specific conditions, can lead to code execution on glibc-based Linux. An attacker can supply a crafted SVG image that, when decoded by sharp through librsvg, may result in arbitrary code execution. |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: shared: fix use-after-free bug when adding shared proxies
The GPIO lookup table can stay alive for longer than the kobject whose
name string's address we're assigning to lookup->dev_id. Fix a potential
UAF by duplicating the string. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: imx: fix slab corruption from undersized DMA bounce buffers
Since commit faa8e404ad8e ("spi: imx: support dynamic burst length for
ECSPI DMA mode"), the driver allocates its private DMA TX/RX buffers
with kzalloc(dma_len), where dma_len is only rounded up to 4 bytes, but
maps, syncs and unmaps them with DMA_CACHE_ALIGNED_LEN(dma_len), i.e.
rounded up to the cache line size. As a result, the DMA API operates on
memory beyond the end of the allocation.
This was observed on a custom i.MX8MP platform with an mcp251xfd CAN
controller under heavy RPMSG load, as a series of refcount_t warnings
triggered from rpmsg_recv_done() in virtio_rpmsg_bus:
refcount_t: addition on 0; use-after-free.
refcount_t: underflow; use-after-free.
refcount_t: saturated; leaking memory.
Leading finally to an "Unable to handle kernel paging request" oops.
Reproducing this problem took between 30 minutes and roughly 30 hours
under the same workload.
Hardware watchpoints on the refcount of a struct rpmsg_endpoint showed
it was overwritten from 2 to 1 by __pi_memcpy_generic() in the
irq/155-spi2.0 thread. Additionally it was found that a "normal"
rpmsg_recv_done() took 11µs +/-2µs from its kref_get to kref_put. In
the error case the same sequence took about 215µs +/-10µs. Based on
this, an LLM was used to identify the size mismatch fixed here.
Allocate the buffers with DMA_CACHE_ALIGNED_LEN(dma_len) so they cover
the full mapped length, and use the same length for
dma_sync_single_for_cpu() to stay consistent with map and unmap.
With this patch applied, the same workload ran for more than 200 hours
without the problem reproducing. |
| Use after free in Windows Autopilot allows an authorized attacker to elevate privileges locally. |
| Use after free in Windows Program Compatibility Assistant Service allows an authorized attacker to elevate privileges locally. |
| Use after free in Windows Storage allows an authorized attacker to elevate privileges locally. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/userq: actually validate userq BOs
This was supposed to loop over the individual evicted list, as the
kernel and always_valid evicted lists were already handled in
amdgpu_vm_validate.
Without this, BOs that were created and evicted before a userq was made
would never end up in an eviction fence rearm.
Also add the missing ref to the BO before drm_exec locks and refs it.
(cherry picked from commit 18decfc9e8cc0fa70b6de9944cc27a37729edfbd) |
| In the Linux kernel, the following vulnerability has been resolved:
sched_ext: Fix use-after-free of a destroyed user DSQ by a deferred reenqueue
A deferred reenqueue can read a freed user DSQ. The request stays on its
CPU's deferred list until run_deferred() takes it, and the RCU callback that
frees the DSQ assumes that the grace period has flushed it, so exit_dsq()
checks the per-CPU node without the deferred list lock. A grace period waits
for readers in flight, not for a pending run_deferred(). A run_deferred()
which starts after the grace period began can detach the request right
before the callback looks and then read the freed DSQ's id.
Cancel the pending requests before the grace period instead. The irq work
that frees the DSQ unlinks every CPU's request under the per-CPU deferred
list lock, and schedule_dsq_reenq() ignores a new request under the same
lock once the id is invalid. Only a run_deferred() that started before the
grace period can hold a request, and it runs with IRQs disabled, so the
grace period waits for it and nothing touches the DSQ after the callback. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: libiscsi: Validate the ITT reflected in a Reject PDU
A Reject PDU carries a copy of the header it rejects, and
iscsi_handle_reject() takes the ITT out of that copy to find the task to
clean up:
memcpy(&rejected_pdu, data, sizeof(struct iscsi_hdr));
...
task = iscsi_itt_to_task(conn, rejected_pdu.itt);
That value is whatever the target put there. iscsi_itt_to_task() bounds
the index against cmds_max and checks nothing else, so any task in the
pool can be named, and iscsi_nop_out_rsp() then completes it.
An index that has never been used gives a NULL task->conn: the pool is
zeroed at session setup and conn is assigned only when a task is
allocated. If the task was used and returned, iscsi_complete_task() hits
its WARN_ON_ONCE(task->state == ISCSI_TASK_FREE) and the refcount
underflows. An in-flight SCSI command is completed as successful - a 1
MiB read returned 1048576 with none of its buffer written and no
warning.
Validate the reflected ITT the way iscsi_itt_to_ctask() validates a
command ITT, and require the task to be in flight and not a SCSI
command.
[ 6.248477] Oops: general protection fault, probably for non-canonical address 0xdffffc000000000c: 0000 [#1] SMP KASAN NOPTI
[ 6.249357] KASAN: null-ptr-deref in range [0x0000000000000060-0x0000000000000067]
[ 6.249951] CPU: 1 UID: 0 PID: 0 Comm: swapper/1 Not tainted 7.2.0-rc5-ISCSI1-gf5098b6bae76 #1 PREEMPT(lazy)
[ 6.250718] Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[ 6.251616] RIP: 0010:iscsi_nop_out_rsp.constprop.0+0x46/0x160
[ 6.252043] Code: c1 ea 03 48 83 ec 08 80 3c 02 00 0f 85 f5 00 00 00 48 b8 00 00 00 00 00 fc ff df 48 8b 6b 58 48 8d 7d 60 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 c0 00 00 00 48 8b 45 60 48 39 c3 74 50 48 b8 00
[ 6.252813] RSP: 0018:ffff88806c907b80 EFLAGS: 00010206
[ 6.253042] RAX: dffffc0000000000 RBX: ffff88800607e000 RCX: ffffffff8d571a25
[ 6.253345] RDX: 000000000000000c RSI: ffff88806c907c38 RDI: 0000000000000060
[ 6.253642] RBP: 0000000000000000 R08: 0000000000000000 R09: fffffbfff235a504
[ 6.253947] R10: 0000000000000003 R11: 7463656e6e6f6320 R12: 0000000000000000
[ 6.254251] R13: 0000000000000000 R14: ffff88806c907c38 R15: 0000000000000000
[ 6.254549] FS: 0000000000000000(0000) GS:ffff8880d95bc000(0000) knlGS:0000000000000000
[ 6.254887] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 6.255140] CR2: 00007fc393e8ffc0 CR3: 0000000005252006 CR4: 0000000000770ef0
[ 6.255439] PKRU: 55555554
[ 6.255564] Call Trace:
[ 6.255674] <IRQ>
[ 6.255768] __iscsi_complete_pdu+0x18bf/0x22a0
[ 6.256733] iscsi_complete_pdu+0x54/0xa0
[ 6.256905] iscsi_tcp_data_recv_done+0xf4/0x250
[ 6.257103] iscsi_tcp_recv_skb+0x31e/0xec0
[ 6.257680] iscsi_sw_tcp_recv+0x12f/0x390
[ 6.258061] __tcp_read_sock+0x1ab/0x810
[ 6.258853] iscsi_sw_tcp_data_ready+0x18b/0x510
[ 6.259808] tcp_data_queue+0x1f13/0x4cd0
[ 6.260567] tcp_rcv_established+0x8a5/0x3a00
[ 6.261931] tcp_v4_do_rcv+0x449/0x960
[ 6.262269] tcp_v4_rcv+0x2245/0x3bc0 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: st: Fix use-after-free race between st_remove() and st_open()
st_remove() drops the probe reference on the scsi_tape with kref_put()
and only afterwards removes its index from st_index_idr. If that was the
last reference, scsi_tape_release() frees the structure while it is
still published in the idr.
scsi_tape_get(), called from st_open(), looks up the tape in
st_index_idr and takes a reference under st_ref_mutex and
st_index_lock. remove_cdevs() does not wait for opens that are already
past chrdev_open(), so an open that is blocked on st_ref_mutex while
st_remove() holds it can take the mutex as soon as st_remove() drops it,
find the freed tpnt in the idr and call kref_get() on it:
BUG: KASAN: slab-use-after-free in st_open
Write of size 4 ...
st_open (drivers/scsi/st.c:254 drivers/scsi/st.c:1291)
chrdev_open
...
Freed by task ...:
kfree
st_remove (drivers/scsi/st.c:4512)
Remove the index from the idr before dropping the reference, all under
st_ref_mutex. A concurrent scsi_tape_get() now either runs first and
holds a valid reference that keeps the tape alive, or runs afterwards
and finds nothing, so st_open() fails with -ENXIO.
This restores the ordering st_remove() had before the conversion to
st_index_idr, where the tape was unpublished from scsi_tapes[] before
the final kref_put(). |
| Use after free in Windows TCP/IP allows an authorized attacker to elevate privileges locally. |
