| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
Input: synaptics-rmi4 - zero report size on F54 work error
In rmi_f54_work(), if an error occurs during report request or command
verification, the code jumped directly to the 'error' label, bypassing
the 'abort' label where f54->report_size was normally zeroed out.
This left f54->report_size containing its previous successful payload
size. If a user then altered the V4L2 format to a smaller size, and a
subsequent run failed, rmi_f54_buffer_queue() would copy the stale,
larger payload size into the shrunken V4L2 buffer, causing a heap
buffer overflow.
Fix this by merging the 'abort' and 'error' labels into a single 'out'
exit path, and ensuring that f54->report_size is always set to 0 on
failure by checking for error and zeroing the local report_size first. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: focaltech - fix array out-of-bounds in focaltech_process_rel_packet
Make finger2 (and also finger1) unsigned, so that if the finger index in
the packet is 0 then subtracting 1 creates an array index which overflows
above the existing check for FOC_MAX_FINGERS, as the existing comment says
it should, instead of writing to state->fingers[-1]. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: SOF: ipc4-pcm: Continue the pipeline trigger in case of IPC timeout
Ignore IPC errors for pipeline state change if the firmware state is
crashed or the IPC has timed out.
If the firmware has crashed the kernel still needs to go through the state
changes to reset its internal to be able to correctly work the next time
the DSP is booted up.
The case with IPC timeout is a bit more problematic, but it has been
rootcaused to be the result of system scheduling blockage and the firmware
did actually received and handled the message, but the reply handling got
blocked by issues outside of the SOF stack.
So far the best way to handle this is to continue with setting the state. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: picolcd: prevent NULL pointer dereference in picolcd_send_and_wait()
In picolcd_send_and_wait(), an integer overflow of the signed loop counter
'k' can theoretically lead to a NULL pointer dereference of 'raw_data'.
If the loop executes more than INT_MAX times, 'k' becomes negative,
making the condition 'k < size' true even when 'size' is 0.
Change the type of 'k' to 'unsigned int' to prevent the overflow and
eliminate the out-of-bounds access.
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
[jkosina@suse.com: extended hash length] |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/hns: Fix memory leak of bonding resources
In a corner case of concurrent driver removal and driver reset,
bonding resource is first released in hns_roce_hw_v2_exit() during
driver removal, and then is allocated again in hns_roce_register_device()
during driver reset. This leads to memory leak because the release
timing has already passed. This may also lead to a kernel panic
as below because of the leaked notifier callback:
Call trace:
0xffffa20fccc04978 (P)
raw_notifier_call_chain+0x20/0x38
call_netdevice_notifiers_info+0x60/0xb8
netdev_lower_state_changed+0x4c/0xb8
As Sashiko suggested, the teardown order of bonding resources should
be inverted to make sure the resources are released when the driver
is removed. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/perf: fix preempt count underflow in fsl_emb_pmu_del
fsl_emb_pmu_del() unconditionally calls put_cpu_var(cpu_hw_events) at
the 'out:' label, but only calls the matching get_cpu_var() after the
'i < 0' early-return check. When event->hw.idx is negative the
function jumps to 'out:' without having taken get_cpu_var(), and the
trailing put_cpu_var() then issues an unmatched preempt_enable(),
underflowing preempt_count.
On a CONFIG_PREEMPT=y kernel preempt_count would underflow and
eventually present as a 'scheduling while atomic' BUG.
Move put_cpu_var() to pair with get_cpu_var() so the percpu access is
correctly bracketed and the 'out:' label only handles perf_pmu_enable. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: idxd: fix double free of wq, engine, and group structs
The release callbacks for wq, engine, and group devices
(idxd_conf_wq_release, idxd_conf_engine_release,
idxd_conf_group_release) each call kfree() on the enclosing struct.
The setup error paths and cleanup functions also call kfree()
explicitly after put_device(), producing a double free whenever
put_device() drops the reference count to zero and fires the release.
In the setup functions, device_initialize() is called before
device_add(), so the reference count is exactly 1 at the error sites.
put_device() unconditionally fires the release, which frees the struct;
the subsequent explicit kfree() then operates on freed memory.
For idxd_setup_wqs(), the wq release callback also owns opcap_bmap
and wqcfg. The error unwind additionally freed those fields explicitly
before calling put_device(), causing further double frees on both.
Remove the redundant explicit kfree() calls from all setup error paths
and cleanup functions for wq, engine, and group structs, delegating
sole ownership of those allocations to the release callbacks. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: sco: Fix a race condition in sco_sock_timeout()
sco_sock_timeout() runs asynchronously and lock_sock(sk). If the socket
is closing while the timer is running, it holds the same lock
(lock_sock(sk)) twice, leading to a deadlock.
CPU 0 CPU 1
==================== ======================
sco_sock_close()
sco_sock_timeout()
lock_sock(sk) // <-- LOCK
__sco_sock_close()
sco_chan_del()
sco_conn_put()
sco_conn_free()
disable_delayed_work_sync()
lock(sk) // <-- SAME LOCK
Fix this by moving disable_delayed_work_sync() outside of lock_sock(sk),
ensuring that no lock_sock(sk) is held before sco_sock_timeout().
Lockdep splat:
WARNING: possible circular locking dependency detected
6.13.0-rc4 #7 Not tainted
syz-executor292/9514 is trying to acquire lock:
ffff8881115d5070 ((work_completion)(&(&conn->timeout_work)->work)){+.+.}-{0:0}, at: rcu_lock_acquire sect/v6.13-rc4/./include/linux/rcupdate.h:337 [inline]
ffff8881115d5070 ((work_completion)(&(&conn->timeout_work)->work)){+.+.}-{0:0}, at: rcu_read_lock sect/v6.13-rc4/./include/linux/rcupdate.h:849 [inline]
ffff8881115d5070 ((work_completion)(&(&conn->timeout_work)->work)){+.+.}-{0:0}, at: start_flush_work sect/v6.13-rc4/kernel/workqueue.c:4137 [inline]
ffff8881115d5070 ((work_completion)(&(&conn->timeout_work)->work)){+.+.}-{0:0}, at: __flush_work+0xd1/0xc40 sect/v6.13-rc4/kernel/workqueue.c:4195
but task is already holding lock:
ffff88807db3a258 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0}, at: lock_sock sect/v6.13-rc4/./include/net/sock.h:1623 [inline]
ffff88807db3a258 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0}, at: sco_sock_close+0x25/0x100 sect/v6.13-rc4/net/bluetooth/sco.c:524
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0}:
lock_acquire+0x1c4/0x520 sect/v6.13-rc4/kernel/locking/lockdep.c:5849
lock_sock_nested+0x48/0x130 sect/v6.13-rc4/net/core/sock.c:3622
lock_sock sect/v6.13-rc4/./include/net/sock.h:1623 [inline]
sco_sock_timeout+0xbe/0x270 sect/v6.13-rc4/net/bluetooth/sco.c:158
process_one_work sect/v6.13-rc4/kernel/workqueue.c:3229 [inline]
process_scheduled_works+0xa99/0x18f0 sect/v6.13-rc4/kernel/workqueue.c:3310
worker_thread+0x8a9/0xd80 sect/v6.13-rc4/kernel/workqueue.c:3391
kthread+0x2c6/0x360 sect/v6.13-rc4/kernel/kthread.c:389
ret_from_fork+0x4e/0x80 sect/v6.13-rc4/arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 sect/v6.13-rc4/arch/x86/entry/entry_64.S:244
-> #0 ((work_completion)(&(&conn->timeout_work)->work)){+.+.}-{0:0}:
check_prev_add sect/v6.13-rc4/kernel/locking/lockdep.c:3161 [inline]
check_prevs_add sect/v6.13-rc4/kernel/locking/lockdep.c:3280 [inline]
validate_chain+0x1888/0x5760 sect/v6.13-rc4/kernel/locking/lockdep.c:3904
__lock_acquire+0x13b4/0x2120 sect/v6.13-rc4/kernel/locking/lockdep.c:5226
lock_acquire+0x1c4/0x520 sect/v6.13-rc4/kernel/locking/lockdep.c:5849
touch_work_lockdep_map sect/v6.13-rc4/kernel/workqueue.c:3909 [inline]
start_flush_work sect/v6.13-rc4/kernel/workqueue.c:4163 [inline]
__flush_work+0x70f/0xc40 sect/v6.13-rc4/kernel/workqueue.c:4195
__cancel_work_sync sect/v6.13-rc4/kernel/workqueue.c:4351 [inline]
disable_delayed_work_sync+0xbb/0xf0 sect/v6.13-rc4/kernel/workqueue.c:4514
sco_conn_free sect/v6.13-rc4/net/bluetooth/sco.c:95 [inline]
kref_put sect/v6.13-rc4/./include/linux/kref.h:65 [inline]
sco_conn_put+0x18f/0x270 sect/v6.13-rc4/net/bluetooth/sco.c:107
sco_chan_del+0xe2/0x210 sect/v6.13-rc4/net/bluetooth/sco.c:236
sco_sock_close+0x8f/0x100 sect/v6.13-rc4/net/bluetooth/sco.c:526
sco_sock_release+0x62/0x2d0 sect/v6.13-rc4/net/blueto
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: core: Initialize hba->rpmbs list in ufshcd
Initialize the hba->rpmbs list in ufshcd_alloc_host() to prevent NULL
pointer dereference in the device teardown path if ufs_rpmb_probe()
fails. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: check if dml21_add_phantom_plane() is successful
Verify that the phantom plane was allocated to avoid a later
segfault.
(cherry picked from commit 5adb54abe5a8e82cbff7f8806db30a5f4924329f) |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: spacemit: fix NULL check in spacemit_pin_set_config
spacemit_pin_set_config() looks up the per-pin descriptor with
spacemit_get_pin() then checks the wrong variable for failure:
const struct spacemit_pin *spin = spacemit_get_pin(pctrl, pin);
...
if (!pin)
return -EINVAL;
reg = spacemit_pin_to_reg(pctrl, spin->pin);
pin is an unsigned int pin id, where 0 (GPIO_0 / gmac0_rxdv on K3) is a
valid pin, so rejecting it here drops the PAD config write for the first
pin of every group. On K3 Pico-ITX the GMAC RGMII group lists pin 0 as
its first entry, so its drive-strength / bias configuration was silently
ignored.
The intended guard is against spacemit_get_pin() returning NULL when the
pin id isn't in the SoC's pin table. Check spin instead, which both
restores PAD setup for pin 0 and prevents a NULL deref on spin->pin. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vmwgfx: enforce cursor size limits for MOB cursors
vmw_cursor_plane_atomic_check() bounds cursor width and height only
on the legacy update path; the SVGA_CAP2_CURSOR_MOB path -- the
default on modern hosts -- accepts any size. When the requested size
exceeds SVGA_REG_CURSOR_MAX_DIMENSION or SVGA_REG_MOB_MAX_SIZE,
vmw_cursor_mob_get() returns -EINVAL and leaves vps->cursor.mob NULL.
Its return value is then discarded in vmw_cursor_plane_prepare_fb(),
so the subsequent vmw_cursor_update_mob() calls
vmw_bo_map_and_cache(NULL) and oopses inside
vmw_bo_map_and_cache_size() on the tbo.base.size load.
Reachable from any DRM master via DRM_IOCTL_MODE_CURSOR2 with a
sufficiently large width or height (e.g. cursor_max_dim + 1).
Reject oversized cursors in atomic_check for both MOB-backed cursor
update types. The MOB byte-size limit only applies to the
SVGA_CAP2_CURSOR_MOB path (vmw_cursor_mob_size() returns 0 for
GB_ONLY); compute the required MOB size in 64-bit to avoid overflow
when very large dimensions are requested.
In prepare_fb only call vmw_cursor_mob_get()/_map() for
VMW_CURSOR_UPDATE_MOB -- the GB_ONLY path uses bo->map.virtual
directly and would otherwise be silently downgraded to NONE on hosts
without SVGA_CAP2_CURSOR_MOB (where vmw_cursor_mob_get() always
returns -EINVAL). Degrade the update to NONE if vmw_cursor_mob_get()
or vmw_cursor_mob_map() fails so the update path does not run with a
NULL backing MOB. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: ccp - Treat zero-length cert chain as query for blob lengths
When handling a PDH export, treat a zero-length userspace cert chain buffer
as a request to query the length of the relevant blobs. Failure to account
for the zero-length buffer trips a BUG_ON() when running with
CONFIG_DEBUG_VIRTUAL=y due to trying to get the physical address of the
ZERO_SIZE_PTR (returned by kzalloc() on the bogus allocation).
kernel BUG at arch/x86/mm/physaddr.c:28 !
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 30 UID: 0 PID: 28580 Comm: syz.2.18 Kdump: loaded
Tainted: G W 6.18.16-smp-DEV #1 NONE
Tainted: [W]=WARN
Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 12.62.0-0 11/19/2025
RIP: 0010:__phys_addr+0x16a/0x180 arch/x86/mm/physaddr.c:28
RSP: 0018:ffffc9008329fc80 EFLAGS: 00010293
RAX: ffffffff8179110a RBX: 0000778000000010 RCX: ffff8884e6992600
RDX: 0000000000000000 RSI: 0000000080000010 RDI: 0000778000000010
RBP: ffffc9008329fdf0 R08: 0000000000000dc0 R09: 00000000ffffffff
R10: dffffc0000000000 R11: fffffbfff126d297 R12: dffffc0000000000
R13: 1ffff92010653fc8 R14: 0000000080000010 R15: dffffc0000000000
FS: 0000555556bec9c0(0000) GS:ffff88aa4ce1c000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fd3159e7000 CR3: 00000004fbc44000 CR4: 0000000000350ef0
Call Trace:
<TASK>
[<ffffffff853d3869>] sev_ioctl_do_pdh_export+0x559/0x7a0 drivers/crypto/ccp/sev-dev.c:2308
[<ffffffff853d1fdd>] sev_ioctl+0x2cd/0x480 drivers/crypto/ccp/sev-dev.c:2556
[<ffffffff82549ebc>] vfs_ioctl fs/ioctl.c:52 [inline]
[<ffffffff82549ebc>] __do_sys_ioctl fs/ioctl.c:598 [inline]
[<ffffffff82549ebc>] __se_sys_ioctl+0xfc/0x170 fs/ioctl.c:584
[<ffffffff8630115f>] do_syscall_x64 arch/x86/entry/syscall_64.c:64 [inline]
[<ffffffff8630115f>] do_syscall_64+0x9f/0xf40 arch/x86/entry/syscall_64.c:98
[<ffffffff81000136>] entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7fd3158eac39
</TASK>
Thankfully, the bug is benign outside of CONFIG_DEBUG_VIRTUAL=y as getting
the physical address is just arithmetic, and the PSP errors out before
trying to write to the garbage address (which it must, otherwise querying
the blob lengths would clobber memory at pfn=0). |
| In the Linux kernel, the following vulnerability has been resolved:
soc: xilinx: Shutdown and free rx mailbox channel
A mbox rx channel is requested using mbox_request_channel_byname() in
probe. In remove callback, the rx mailbox channel is cleaned up when the
rx_chan is NULL due to incorrect condition check. The mailbox channel is
not shutdown and it can receive messages even after the device removal.
This leads to use after free. Also the channel resources are not freed.
Fix this by checking the rx_chan correctly. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (sht3x) Fix unaligned accesses
Sashiko reports:
In sht3x_update_client(), the 16-bit temperature and humidity values are
extracted from a stack-allocated byte array using be16_to_cpup(). The
pointers passed to this function are calculated as buf and buf + 3. Since
the difference between the two pointers is an odd number of bytes, at
least one of them is guaranteed to be at an unaligned offset.
This will trigger an alignment fault on strict-alignment architectures
such as ARMv5 or SPARC, resulting in a kernel panic.
Fix the problem by using get_unaligned_be16() instead of be16_to_cpup(),
and put_unaligned_be16() instead of cpu_to_be16(). |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: vgic: Avoid double-deactivate of IRQs in the nested context
In the nested state, the physical interrupt has already been
deactivated through the HW bit in the LR. The extra deactivation
would be harmless but can hit an errata case on AmpereOne, so
avoid it here.
On AmpereOne, deactivating a physical interrupt through
ICC_DIR_EL1 or ICC_EOIR1_EL1 (depending on EOImode) which is not
active, but is the highest priority pending interrupt causes the
cpu to lose the interrupt pending state and also prevents the
delivery of future interrupts. |
| In the Linux kernel, the following vulnerability has been resolved:
iommufd/viommu: Release the igroup lock on the vdevice_size error path
iommufd_vdevice_alloc_ioctl() takes idev->igroup->lock, then validates the
driver's vdevice_size against the core structure size with a WARN_ON_ONCE.
On failure that guard jumps to out_put_idev, below out_unlock_igroup, so it
skips the mutex_unlock(), leaving the igroup lock held and deadlocking the
next vDEVICE operation on that group.
Jump to out_unlock_igroup instead. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (occ) unregister sysfs devices outside occ lock
occ_active(false) and occ_shutdown() unregister sysfs-backed devices while
occ->lock is held. hwmon_device_unregister() and sysfs_remove_group() can
wait for active sysfs callbacks to drain, and those callbacks can enter the
OCC update path and try to take occ->lock again. That gives the unregister
paths the lock ordering occ->lock -> sysfs callback drain, while a callback
has the opposite edge sysfs callback -> occ->lock.
This issue was found by our static analysis tool and then manually
reviewed against the current tree.
The grounded PoC kept the real unregister and callback carrier:
occ_shutdown()
hwmon_device_unregister()
occ_show_temp_1()
occ_update_response()
Lockdep reported the circular dependency with occ_shutdown() already
holding the OCC mutex and hwmon_device_unregister() waiting on the sysfs
side:
WARNING: possible circular locking dependency detected
... (sysfs_lock) ... at: hwmon_device_unregister+0x12/0x30 [vuln_msv]
... (&test_occ.lock) ... at: occ_shutdown.constprop.0+0xe/0x40 [vuln_msv]
occ_update_response.isra.0+0xb/0x20 [vuln_msv]
occ_show_temp_1.constprop.0.isra.0+0x23/0x40 [vuln_msv]
*** DEADLOCK ***
Serialize hwmon registration and removal with a separate hwmon_lock.
Under that lock, detach occ->hwmon and update occ->active while occ->lock
is held so concurrent OCC state changes still see a stable state, then
drop occ->lock before calling hwmon_device_unregister(). Remove the
driver sysfs group before taking occ->lock in occ_shutdown(), so draining
the driver attributes cannot wait while the OCC mutex is held. Also make
OCC update callbacks return -ENODEV after deactivation, so callbacks that
already passed sysfs active protection do not poll the hardware after
teardown has detached the hwmon device. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: migrate_device: fix pte_pfn/pte_dirty called on non-present PTE
pte_pfn() and pte_dirty() have undefined behaviour when called on a
non-present PTE. In migrate_vma_collect_pmd(), these functions may be
invoked on non-present entries (e.g., device-private entries), leading
to potential crashes from pte_pfn() or incorrect dirty folio accounting
from pte_dirty(). Fix both by guarding with pte_present() checks. |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: drop __init from vec_check_unaligned_access_speed_all_cpus
This function runs within a kthread and need not necessarily finish
before system finishes boot and free_initmem() unmaps the .init.text
section. This function makes calls to SBI for probing unaligned access
speed, and if this is slow for some reason (say some debug prints were
added to SBI), the kthread can still be running at this point and result
in an instruction page fault when trying to fetch from the freed region.
[ 25.642087] Unable to handle kernel paging request at virtual address ffffffff80a04ef8
[ 25.646694] Current vec_check_unali pgtable: 4K pagesize, 48-bit VAs, pgdp=0x00004000316e9000
[ 25.653170] [ffffffff80a04ef8] pgd=000010004be7e401, p4d=000010004be7e401, pud=000010004be7e001, pmd=000010000c3000e3
[ 25.661244] Oops [#1]
[ 25.662997] Modules linked in:
[ 25.665357] CPU: 3 UID: 0 PID: 42 Comm: vec_check_unali Not tainted 7.0.0-tt-blackhole-asrinivasan-00007-g30ff73f18211 #570 PREEMPTLAZY
[ 25.674669] Hardware name: Tenstorrent Blackhole (DT)
[ 25.678545] epc : vec_check_unaligned_access_speed_all_cpus+0x18/0x2c
[ 25.683458] ra : vec_check_unaligned_access_speed_all_cpus+0x18/0x2c
[ 25.688372] epc : ffffffff80a04ef8 ra : ffffffff80a04ef8 sp : ffff8f8000203e20
[ 25.693874] gp : ffffffff814dc168 tp : ffffaf8001ad9900 t0 : 0000000000000000
[ 25.699401] t1 : fffffffffffffff0 t2 : ffffaf8001ad9a10 s0 : ffff8f8000203e30
[ 25.704912] s1 : ffffaf80018dc780 a0 : 0000000000000000 a1 : 0000000000000002
[ 25.710407] a2 : 00000000000001f0 a3 : 0000000000000018 a4 : 0000000000000000
[ 25.715917] a5 : 0000000000000000 a6 : ffffaf8001c03d98 a7 : ffffaf8001c03e30
[ 25.721419] s2 : ffff8f8000023c98 s3 : ffffaf8001aa1240 s4 : ffffffff80a04ee0
[ 25.726937] s5 : 0000000000000000 s6 : 0000000000000000 s7 : 0000000000000000
[ 25.732450] s8 : 0000000000000000 s9 : 0000000000000000 s10: 0000000000000000
[ 25.737944] s11: 0000000000000000 t3 : 0000000000000002 t4 : 0000000000000402
[ 25.743481] t5 : 0000000000000040 t6 : 0000000000000004 ssp : 0000000000000000
[ 25.749024] status: 0000000200000120 badaddr: ffffffff80a04ef8 cause: 000000000000000c
[ 25.755060] [<ffffffff80a04ef8>] vec_check_unaligned_access_speed_all_cpus+0x18/0x2c
[ 25.760964] [<ffffffff80047a10>] kthread+0xd8/0xfc
[ 25.764660] [<ffffffff80010c48>] ret_from_fork_kernel+0x18/0x1c4
[ 25.769220] [<ffffffff80895fe6>] ret_from_fork_kernel_asm+0x16/0x18
[ 25.774018] Code: cccc cccc cccc cccc cccc cccc cccc cccc cccc cccc (cccc) cccc
Drop __init from its signature so that this doesn't happen. |
