| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| NULL Pointer Dereference vulnerability in Avast Antivirus on MacOS, Avast Anitvirus on Linux when scanning a malformed Windows PE file causes the antivirus process to crash.This issue affects Antivirus: 16.0.0; Anitvirus: 3.0.3. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/sysfb: Do not dereference NULL pointer in plane reset
The plane state in __drm_gem_reset_shadow_plane() can be NULL. Do not
deref that pointer, but forward NULL to the other plane-reset helpers.
Clears plane->state to NULL.
v2:
- fix typo in commit description (Javier) |
| A local privilege-escalation vulnerability has been discovered in the HPE Aruba Networking Virtual Intranet Access (VIA) client. Successful exploitation of this vulnerability could allow a local attacker to achieve arbitrary code execution with root privileges. |
| In the Linux kernel before 4.8, usb_parse_endpoint in drivers/usb/core/config.c does not validate the wMaxPacketSize field of an endpoint descriptor. NOTE: This vulnerability only affects products that are no longer supported by the supplier. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: storage: Fix memory leak in USB bulk transport
A kernel memory leak was identified by the 'ioctl_sg01' test from Linux
Test Project (LTP). The following bytes were mainly observed: 0x53425355.
When USB storage devices incorrectly skip the data phase with status data,
the code extracts/validates the CSW from the sg buffer, but fails to clear
it afterwards. This leaves status protocol data in srb's transfer buffer,
such as the US_BULK_CS_SIGN 'USBS' signature observed here. Thus, this can
lead to USB protocols leaks to user space through SCSI generic (/dev/sg*)
interfaces, such as the one seen here when the LTP test requested 512 KiB.
Fix the leak by zeroing the CSW data in srb's transfer buffer immediately
after the validation of devices that skip data phase.
Note: Differently from CVE-2018-1000204, which fixed a big leak by zero-
ing pages at allocation time, this leak occurs after allocation, when USB
protocol data is written to already-allocated sg pages. |
| In the Linux kernel, the following vulnerability has been resolved:
media: iris: Fix memory leak by freeing untracked persist buffer
One internal buffer which is allocated only once per session was not
being freed during session close because it was not being tracked as
part of internal buffer list which resulted in a memory leak.
Add the necessary logic to explicitly free the untracked internal buffer
during session close to ensure all allocated memory is released
properly. |
| In the Linux kernel, the following vulnerability has been resolved:
phy: stm32-usphyc: Fix off by one in probe()
The "index" variable is used as an index into the usbphyc->phys[] array
which has usbphyc->nphys elements. So if it is equal to usbphyc->nphys
then it is one element out of bounds. The "index" comes from the
device tree so it's data that we trust and it's unlikely to be wrong,
however it's obviously still worth fixing the bug. Change the > to >=. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: xilinx: xdma: Fix regmap max_register
The max_register field is assigned the size of the register memory
region instead of the offset of the last register.
The result is that reading from the regmap via debugfs can cause
a segmentation fault:
tail /sys/kernel/debug/regmap/xdma.1.auto/registers
Unable to handle kernel paging request at virtual address ffff800082f70000
Mem abort info:
ESR = 0x0000000096000007
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x07: level 3 translation fault
[...]
Call trace:
regmap_mmio_read32le+0x10/0x30
_regmap_bus_reg_read+0x74/0xc0
_regmap_read+0x68/0x198
regmap_read+0x54/0x88
regmap_read_debugfs+0x140/0x380
regmap_map_read_file+0x30/0x48
full_proxy_read+0x68/0xc8
vfs_read+0xcc/0x310
ksys_read+0x7c/0x120
__arm64_sys_read+0x24/0x40
invoke_syscall.constprop.0+0x64/0x108
do_el0_svc+0xb0/0xd8
el0_svc+0x38/0x130
el0t_64_sync_handler+0x120/0x138
el0t_64_sync+0x194/0x198
Code: aa1e03e9 d503201f f9400000 8b214000 (b9400000)
---[ end trace 0000000000000000 ]---
note: tail[1217] exited with irqs disabled
note: tail[1217] exited with preempt_count 1
Segmentation fault |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs3: pretend $Extend records as regular files
Since commit af153bb63a33 ("vfs: catch invalid modes in may_open()")
requires any inode be one of S_IFDIR/S_IFLNK/S_IFREG/S_IFCHR/S_IFBLK/
S_IFIFO/S_IFSOCK type, use S_IFREG for $Extend records. |
| VestaCP commit a3f0fa1 (2018-05-31) up to commit ee03eff (2018-06-13) contain embedded malicious code that resulted in a supply-chain compromise. New installations created from the compromised installer since at least May 2018 were subject to installation of Linux/ChachaDDoS, a multi-stage DDoS bot that uses Lua for second- and third-stage components. The compromise leaked administrative credentials (base64-encoded admin password and server domain) to an external URL during installation and/or resulted in the installer dropping and executing a DDoS malware payload under local system privileges. Compromised servers were subsequently observed participating in large-scale DDoS activity. Vesta acknowledged exploitation in the wild in October 2018. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: silence the warning when evicting inode with dioread_nolock
When evicting an inode with default dioread_nolock, it could be raced by
the unwritten extents converting kworker after writeback some new
allocated dirty blocks. It convert unwritten extents to written, the
extents could be merged to upper level and free extent blocks, so it
could mark the inode dirty again even this inode has been marked
I_FREEING. But the inode->i_io_list check and warning in
ext4_evict_inode() missing this corner case. Fortunately,
ext4_evict_inode() will wait all extents converting finished before this
check, so it will not lead to inode use-after-free problem, every thing
is OK besides this warning. The WARN_ON_ONCE was originally designed
for finding inode use-after-free issues in advance, but if we add
current dioread_nolock case in, it will become not quite useful, so fix
this warning by just remove this check.
======
WARNING: CPU: 7 PID: 1092 at fs/ext4/inode.c:227
ext4_evict_inode+0x875/0xc60
...
RIP: 0010:ext4_evict_inode+0x875/0xc60
...
Call Trace:
<TASK>
evict+0x11c/0x2b0
iput+0x236/0x3a0
do_unlinkat+0x1b4/0x490
__x64_sys_unlinkat+0x4c/0xb0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7fa933c1115b
======
rm kworker
ext4_end_io_end()
vfs_unlink()
ext4_unlink()
ext4_convert_unwritten_io_end_vec()
ext4_convert_unwritten_extents()
ext4_map_blocks()
ext4_ext_map_blocks()
ext4_ext_try_to_merge_up()
__mark_inode_dirty()
check !I_FREEING
locked_inode_to_wb_and_lock_list()
iput()
iput_final()
evict()
ext4_evict_inode()
truncate_inode_pages_final() //wait release io_end
inode_io_list_move_locked()
ext4_release_io_end()
trigger WARN_ON_ONCE() |
| In the Linux kernel, the following vulnerability has been resolved:
futex: Don't leak robust_list pointer on exec race
sys_get_robust_list() and compat_get_robust_list() use ptrace_may_access()
to check if the calling task is allowed to access another task's
robust_list pointer. This check is racy against a concurrent exec() in the
target process.
During exec(), a task may transition from a non-privileged binary to a
privileged one (e.g., setuid binary) and its credentials/memory mappings
may change. If get_robust_list() performs ptrace_may_access() before
this transition, it may erroneously allow access to sensitive information
after the target becomes privileged.
A racy access allows an attacker to exploit a window during which
ptrace_may_access() passes before a target process transitions to a
privileged state via exec().
For example, consider a non-privileged task T that is about to execute a
setuid-root binary. An attacker task A calls get_robust_list(T) while T
is still unprivileged. Since ptrace_may_access() checks permissions
based on current credentials, it succeeds. However, if T begins exec
immediately afterwards, it becomes privileged and may change its memory
mappings. Because get_robust_list() proceeds to access T->robust_list
without synchronizing with exec() it may read user-space pointers from a
now-privileged process.
This violates the intended post-exec access restrictions and could
expose sensitive memory addresses or be used as a primitive in a larger
exploit chain. Consequently, the race can lead to unauthorized
disclosure of information across privilege boundaries and poses a
potential security risk.
Take a read lock on signal->exec_update_lock prior to invoking
ptrace_may_access() and accessing the robust_list/compat_robust_list.
This ensures that the target task's exec state remains stable during the
check, allowing for consistent and synchronized validation of
credentials. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: check device's attached status in compat ioctls
Syzbot identified an issue [1] that crashes kernel, seemingly due to
unexistent callback dev->get_valid_routes(). By all means, this should
not occur as said callback must always be set to
get_zero_valid_routes() in __comedi_device_postconfig().
As the crash seems to appear exclusively in i386 kernels, at least,
judging from [1] reports, the blame lies with compat versions
of standard IOCTL handlers. Several of them are modified and
do not use comedi_unlocked_ioctl(). While functionality of these
ioctls essentially copy their original versions, they do not
have required sanity check for device's attached status. This,
in turn, leads to a possibility of calling select IOCTLs on a
device that has not been properly setup, even via COMEDI_DEVCONFIG.
Doing so on unconfigured devices means that several crucial steps
are missed, for instance, specifying dev->get_valid_routes()
callback.
Fix this somewhat crudely by ensuring device's attached status before
performing any ioctls, improving logic consistency between modern
and compat functions.
[1] Syzbot report:
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
CR2: ffffffffffffffd6 CR3: 000000006c717000 CR4: 0000000000352ef0
Call Trace:
<TASK>
get_valid_routes drivers/comedi/comedi_fops.c:1322 [inline]
parse_insn+0x78c/0x1970 drivers/comedi/comedi_fops.c:1401
do_insnlist_ioctl+0x272/0x700 drivers/comedi/comedi_fops.c:1594
compat_insnlist drivers/comedi/comedi_fops.c:3208 [inline]
comedi_compat_ioctl+0x810/0x990 drivers/comedi/comedi_fops.c:3273
__do_compat_sys_ioctl fs/ioctl.c:695 [inline]
__se_compat_sys_ioctl fs/ioctl.c:638 [inline]
__ia32_compat_sys_ioctl+0x242/0x370 fs/ioctl.c:638
do_syscall_32_irqs_on arch/x86/entry/syscall_32.c:83 [inline]
... |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: multiq3: sanitize config options in multiq3_attach()
Syzbot identified an issue [1] in multiq3_attach() that induces a
task timeout due to open() or COMEDI_DEVCONFIG ioctl operations,
specifically, in the case of multiq3 driver.
This problem arose when syzkaller managed to craft weird configuration
options used to specify the number of channels in encoder subdevice.
If a particularly great number is passed to s->n_chan in
multiq3_attach() via it->options[2], then multiple calls to
multiq3_encoder_reset() at the end of driver-specific attach() method
will be running for minutes, thus blocking tasks and affected devices
as well.
While this issue is most likely not too dangerous for real-life
devices, it still makes sense to sanitize configuration inputs. Enable
a sensible limit on the number of encoder chips (4 chips max, each
with 2 channels) to stop this behaviour from manifesting.
[1] Syzbot crash:
INFO: task syz.2.19:6067 blocked for more than 143 seconds.
...
Call Trace:
<TASK>
context_switch kernel/sched/core.c:5254 [inline]
__schedule+0x17c4/0x4d60 kernel/sched/core.c:6862
__schedule_loop kernel/sched/core.c:6944 [inline]
schedule+0x165/0x360 kernel/sched/core.c:6959
schedule_preempt_disabled+0x13/0x30 kernel/sched/core.c:7016
__mutex_lock_common kernel/locking/mutex.c:676 [inline]
__mutex_lock+0x7e6/0x1350 kernel/locking/mutex.c:760
comedi_open+0xc0/0x590 drivers/comedi/comedi_fops.c:2868
chrdev_open+0x4cc/0x5e0 fs/char_dev.c:414
do_dentry_open+0x953/0x13f0 fs/open.c:965
vfs_open+0x3b/0x340 fs/open.c:1097
... |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: pcl818: fix null-ptr-deref in pcl818_ai_cancel()
Syzbot identified an issue [1] in pcl818_ai_cancel(), which stems from
the fact that in case of early device detach via pcl818_detach(),
subdevice dev->read_subdev may not have initialized its pointer to
&struct comedi_async as intended. Thus, any such dereferencing of
&s->async->cmd will lead to general protection fault and kernel crash.
Mitigate this problem by removing a call to pcl818_ai_cancel() from
pcl818_detach() altogether. This way, if the subdevice setups its
support for async commands, everything async-related will be
handled via subdevice's own ->cancel() function in
comedi_device_detach_locked() even before pcl818_detach(). If no
support for asynchronous commands is provided, there is no need
to cancel anything either.
[1] Syzbot crash:
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000005: 0000 [#1] SMP KASAN PTI
KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f]
CPU: 1 UID: 0 PID: 6050 Comm: syz.0.18 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/18/2025
RIP: 0010:pcl818_ai_cancel+0x69/0x3f0 drivers/comedi/drivers/pcl818.c:762
...
Call Trace:
<TASK>
pcl818_detach+0x66/0xd0 drivers/comedi/drivers/pcl818.c:1115
comedi_device_detach_locked+0x178/0x750 drivers/comedi/drivers.c:207
do_devconfig_ioctl drivers/comedi/comedi_fops.c:848 [inline]
comedi_unlocked_ioctl+0xcde/0x1020 drivers/comedi/comedi_fops.c:2178
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:597 [inline]
... |
| In the Linux kernel, the following vulnerability has been resolved:
backlight: led-bl: Add devlink to supplier LEDs
LED Backlight is a consumer of one or multiple LED class devices, but
devlink is currently unable to create correct supplier-producer links when
the supplier is a class device. It creates instead a link where the
supplier is the parent of the expected device.
One consequence is that removal order is not correctly enforced.
Issues happen for example with the following sections in a device tree
overlay:
// An LED driver chip
pca9632@62 {
compatible = "nxp,pca9632";
reg = <0x62>;
// ...
addon_led_pwm: led-pwm@3 {
reg = <3>;
label = "addon:led:pwm";
};
};
backlight-addon {
compatible = "led-backlight";
leds = <&addon_led_pwm>;
brightness-levels = <255>;
default-brightness-level = <255>;
};
In this example, the devlink should be created between the backlight-addon
(consumer) and the pca9632@62 (supplier). Instead it is created between the
backlight-addon (consumer) and the parent of the pca9632@62, which is
typically the I2C bus adapter.
On removal of the above overlay, the LED driver can be removed before the
backlight device, resulting in:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
...
Call trace:
led_put+0xe0/0x140
devm_led_release+0x6c/0x98
Another way to reproduce the bug without any device tree overlays is
unbinding the LED class device (pca9632@62) before unbinding the consumer
(backlight-addon):
echo 11-0062 >/sys/bus/i2c/drivers/leds-pca963x/unbind
echo ...backlight-dock >/sys/bus/platform/drivers/led-backlight/unbind
Fix by adding a devlink between the consuming led-backlight device and the
supplying LED device, as other drivers and subsystems do as well. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: invalidate dentry cache on failed whiteout creation
F2FS can mount filesystems with corrupted directory depth values that
get runtime-clamped to MAX_DIR_HASH_DEPTH. When RENAME_WHITEOUT
operations are performed on such directories, f2fs_rename performs
directory modifications (updating target entry and deleting source
entry) before attempting to add the whiteout entry via f2fs_add_link.
If f2fs_add_link fails due to the corrupted directory structure, the
function returns an error to VFS, but the partial directory
modifications have already been committed to disk. VFS assumes the
entire rename operation failed and does not update the dentry cache,
leaving stale mappings.
In the error path, VFS does not call d_move() to update the dentry
cache. This results in new_dentry still pointing to the old inode
(new_inode) which has already had its i_nlink decremented to zero.
The stale cache causes subsequent operations to incorrectly reference
the freed inode.
This causes subsequent operations to use cached dentry information that
no longer matches the on-disk state. When a second rename targets the
same entry, VFS attempts to decrement i_nlink on the stale inode, which
may already have i_nlink=0, triggering a WARNING in drop_nlink().
Example sequence:
1. First rename (RENAME_WHITEOUT): file2 → file1
- f2fs updates file1 entry on disk (points to inode 8)
- f2fs deletes file2 entry on disk
- f2fs_add_link(whiteout) fails (corrupted directory)
- Returns error to VFS
- VFS does not call d_move() due to error
- VFS cache still has: file1 → inode 7 (stale!)
- inode 7 has i_nlink=0 (already decremented)
2. Second rename: file3 → file1
- VFS uses stale cache: file1 → inode 7
- Tries to drop_nlink on inode 7 (i_nlink already 0)
- WARNING in drop_nlink()
Fix this by explicitly invalidating old_dentry and new_dentry when
f2fs_add_link fails during whiteout creation. This forces VFS to
refresh from disk on subsequent operations, ensuring cache consistency
even when the rename partially succeeds.
Reproducer:
1. Mount F2FS image with corrupted i_current_depth
2. renameat2(file2, file1, RENAME_WHITEOUT)
3. renameat2(file3, file1, 0)
4. System triggers WARNING in drop_nlink() |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: set dummy blocksize to read boot_block when mounting
When mounting, sb->s_blocksize is used to read the boot_block without
being defined or validated. Set a dummy blocksize before attempting to
read the boot_block.
The issue can be triggered with the following syz reproducer:
mkdirat(0xffffffffffffff9c, &(0x7f0000000080)='./file1\x00', 0x0)
r4 = openat$nullb(0xffffffffffffff9c, &(0x7f0000000040), 0x121403, 0x0)
ioctl$FS_IOC_SETFLAGS(r4, 0x40081271, &(0x7f0000000980)=0x4000)
mount(&(0x7f0000000140)=@nullb, &(0x7f0000000040)='./cgroup\x00',
&(0x7f0000000000)='ntfs3\x00', 0x2208004, 0x0)
syz_clone(0x88200200, 0x0, 0x0, 0x0, 0x0, 0x0)
Here, the ioctl sets the bdev block size to 16384. During mount,
get_tree_bdev_flags() calls sb_set_blocksize(sb, block_size(bdev)),
but since block_size(bdev) > PAGE_SIZE, sb_set_blocksize() leaves
sb->s_blocksize at zero.
Later, ntfs_init_from_boot() attempts to read the boot_block while
sb->s_blocksize is still zero, which triggers the bug.
[almaz.alexandrovich@paragon-software.com: changed comment style, added
return value handling] |
| In the Linux kernel, the following vulnerability has been resolved:
fuse: fix readahead reclaim deadlock
Commit e26ee4efbc79 ("fuse: allocate ff->release_args only if release is
needed") skips allocating ff->release_args if the server does not
implement open. However in doing so, fuse_prepare_release() now skips
grabbing the reference on the inode, which makes it possible for an
inode to be evicted from the dcache while there are inflight readahead
requests. This causes a deadlock if the server triggers reclaim while
servicing the readahead request and reclaim attempts to evict the inode
of the file being read ahead. Since the folio is locked during
readahead, when reclaim evicts the fuse inode and fuse_evict_inode()
attempts to remove all folios associated with the inode from the page
cache (truncate_inode_pages_range()), reclaim will block forever waiting
for the lock since readahead cannot relinquish the lock because it is
itself blocked in reclaim:
>>> stack_trace(1504735)
folio_wait_bit_common (mm/filemap.c:1308:4)
folio_lock (./include/linux/pagemap.h:1052:3)
truncate_inode_pages_range (mm/truncate.c:336:10)
fuse_evict_inode (fs/fuse/inode.c:161:2)
evict (fs/inode.c:704:3)
dentry_unlink_inode (fs/dcache.c:412:3)
__dentry_kill (fs/dcache.c:615:3)
shrink_kill (fs/dcache.c:1060:12)
shrink_dentry_list (fs/dcache.c:1087:3)
prune_dcache_sb (fs/dcache.c:1168:2)
super_cache_scan (fs/super.c:221:10)
do_shrink_slab (mm/shrinker.c:435:9)
shrink_slab (mm/shrinker.c:626:10)
shrink_node (mm/vmscan.c:5951:2)
shrink_zones (mm/vmscan.c:6195:3)
do_try_to_free_pages (mm/vmscan.c:6257:3)
do_swap_page (mm/memory.c:4136:11)
handle_pte_fault (mm/memory.c:5562:10)
handle_mm_fault (mm/memory.c:5870:9)
do_user_addr_fault (arch/x86/mm/fault.c:1338:10)
handle_page_fault (arch/x86/mm/fault.c:1481:3)
exc_page_fault (arch/x86/mm/fault.c:1539:2)
asm_exc_page_fault+0x22/0x27
Fix this deadlock by allocating ff->release_args and grabbing the
reference on the inode when preparing the file for release even if the
server does not implement open. The inode reference will be dropped when
the last reference on the fuse file is dropped (see fuse_file_put() ->
fuse_release_end()). |
| In the Linux kernel, the following vulnerability has been resolved:
block: fix race between wbt_enable_default and IO submission
When wbt_enable_default() is moved out of queue freezing in elevator_change(),
it can cause the wbt inflight counter to become negative (-1), leading to hung
tasks in the writeback path. Tasks get stuck in wbt_wait() because the counter
is in an inconsistent state.
The issue occurs because wbt_enable_default() could race with IO submission,
allowing the counter to be decremented before proper initialization. This manifests
as:
rq_wait[0]:
inflight: -1
has_waiters: True
rwb_enabled() checks the state, which can be updated exactly between wbt_wait()
(rq_qos_throttle()) and wbt_track()(rq_qos_track()), then the inflight counter
will become negative.
And results in hung task warnings like:
task:kworker/u24:39 state:D stack:0 pid:14767
Call Trace:
rq_qos_wait+0xb4/0x150
wbt_wait+0xa9/0x100
__rq_qos_throttle+0x24/0x40
blk_mq_submit_bio+0x672/0x7b0
...
Fix this by:
1. Splitting wbt_enable_default() into:
- __wbt_enable_default(): Returns true if wbt_init() should be called
- wbt_enable_default(): Wrapper for existing callers (no init)
- wbt_init_enable_default(): New function that checks and inits WBT
2. Using wbt_init_enable_default() in blk_register_queue() to ensure
proper initialization during queue registration
3. Move wbt_init() out of wbt_enable_default() which is only for enabling
disabled wbt from bfq and iocost, and wbt_init() isn't needed. Then the
original lock warning can be avoided.
4. Removing the ELEVATOR_FLAG_ENABLE_WBT_ON_EXIT flag and its handling
code since it's no longer needed
This ensures WBT is properly initialized before any IO can be submitted,
preventing the counter from going negative. |
