| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btusb: mediatek: Avoid btusb_mtk_claim_iso_intf() NULL deref
In btusb_mtk_setup(), we set `btmtk_data->isopkt_intf` to:
usb_ifnum_to_if(data->udev, MTK_ISO_IFNUM)
That function can return NULL in some cases. Even when it returns
NULL, though, we still go on to call btusb_mtk_claim_iso_intf().
As of commit e9087e828827 ("Bluetooth: btusb: mediatek: Add locks for
usb_driver_claim_interface()"), calling btusb_mtk_claim_iso_intf()
when `btmtk_data->isopkt_intf` is NULL will cause a crash because
we'll end up passing a bad pointer to device_lock(). Prior to that
commit we'd pass the NULL pointer directly to
usb_driver_claim_interface() which would detect it and return an
error, which was handled.
Resolve the crash in btusb_mtk_claim_iso_intf() by adding a NULL check
at the start of the function. This makes the code handle a NULL
`btmtk_data->isopkt_intf` the same way it did before the problematic
commit (just with a slight change to the error message printed). |
| In the Linux kernel, the following vulnerability has been resolved:
rcuscale: Move rcu_scale_writer() schedule_timeout_uninterruptible() to _idle()
The rcuscale.holdoff module parameter can be used to delay the start
of rcu_scale_writer() kthread. However, the hung-task timeout will
trigger when the timeout specified by rcuscale.holdoff is greater than
hung_task_timeout_secs:
runqemu kvm nographic slirp qemuparams="-smp 4 -m 2048M"
bootparams="rcuscale.shutdown=0 rcuscale.holdoff=300"
[ 247.071753] INFO: task rcu_scale_write:59 blocked for more than 122 seconds.
[ 247.072529] Not tainted 6.4.0-rc1-00134-gb9ed6de8d4ff #7
[ 247.073400] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 247.074331] task:rcu_scale_write state:D stack:30144 pid:59 ppid:2 flags:0x00004000
[ 247.075346] Call Trace:
[ 247.075660] <TASK>
[ 247.075965] __schedule+0x635/0x1280
[ 247.076448] ? __pfx___schedule+0x10/0x10
[ 247.076967] ? schedule_timeout+0x2dc/0x4d0
[ 247.077471] ? __pfx_lock_release+0x10/0x10
[ 247.078018] ? enqueue_timer+0xe2/0x220
[ 247.078522] schedule+0x84/0x120
[ 247.078957] schedule_timeout+0x2e1/0x4d0
[ 247.079447] ? __pfx_schedule_timeout+0x10/0x10
[ 247.080032] ? __pfx_rcu_scale_writer+0x10/0x10
[ 247.080591] ? __pfx_process_timeout+0x10/0x10
[ 247.081163] ? __pfx_sched_set_fifo_low+0x10/0x10
[ 247.081760] ? __pfx_rcu_scale_writer+0x10/0x10
[ 247.082287] rcu_scale_writer+0x6b1/0x7f0
[ 247.082773] ? mark_held_locks+0x29/0xa0
[ 247.083252] ? __pfx_rcu_scale_writer+0x10/0x10
[ 247.083865] ? __pfx_rcu_scale_writer+0x10/0x10
[ 247.084412] kthread+0x179/0x1c0
[ 247.084759] ? __pfx_kthread+0x10/0x10
[ 247.085098] ret_from_fork+0x2c/0x50
[ 247.085433] </TASK>
This commit therefore replaces schedule_timeout_uninterruptible() with
schedule_timeout_idle(). |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: Fix an uninit variable access bug in __ip6_make_skb()
Syzbot reported a bug as following:
=====================================================
BUG: KMSAN: uninit-value in arch_atomic64_inc arch/x86/include/asm/atomic64_64.h:88 [inline]
BUG: KMSAN: uninit-value in arch_atomic_long_inc include/linux/atomic/atomic-long.h:161 [inline]
BUG: KMSAN: uninit-value in atomic_long_inc include/linux/atomic/atomic-instrumented.h:1429 [inline]
BUG: KMSAN: uninit-value in __ip6_make_skb+0x2f37/0x30f0 net/ipv6/ip6_output.c:1956
arch_atomic64_inc arch/x86/include/asm/atomic64_64.h:88 [inline]
arch_atomic_long_inc include/linux/atomic/atomic-long.h:161 [inline]
atomic_long_inc include/linux/atomic/atomic-instrumented.h:1429 [inline]
__ip6_make_skb+0x2f37/0x30f0 net/ipv6/ip6_output.c:1956
ip6_finish_skb include/net/ipv6.h:1122 [inline]
ip6_push_pending_frames+0x10e/0x550 net/ipv6/ip6_output.c:1987
rawv6_push_pending_frames+0xb12/0xb90 net/ipv6/raw.c:579
rawv6_sendmsg+0x297e/0x2e60 net/ipv6/raw.c:922
inet_sendmsg+0x101/0x180 net/ipv4/af_inet.c:827
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg net/socket.c:734 [inline]
____sys_sendmsg+0xa8e/0xe70 net/socket.c:2476
___sys_sendmsg+0x2a1/0x3f0 net/socket.c:2530
__sys_sendmsg net/socket.c:2559 [inline]
__do_sys_sendmsg net/socket.c:2568 [inline]
__se_sys_sendmsg net/socket.c:2566 [inline]
__x64_sys_sendmsg+0x367/0x540 net/socket.c:2566
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Uninit was created at:
slab_post_alloc_hook mm/slab.h:766 [inline]
slab_alloc_node mm/slub.c:3452 [inline]
__kmem_cache_alloc_node+0x71f/0xce0 mm/slub.c:3491
__do_kmalloc_node mm/slab_common.c:967 [inline]
__kmalloc_node_track_caller+0x114/0x3b0 mm/slab_common.c:988
kmalloc_reserve net/core/skbuff.c:492 [inline]
__alloc_skb+0x3af/0x8f0 net/core/skbuff.c:565
alloc_skb include/linux/skbuff.h:1270 [inline]
__ip6_append_data+0x51c1/0x6bb0 net/ipv6/ip6_output.c:1684
ip6_append_data+0x411/0x580 net/ipv6/ip6_output.c:1854
rawv6_sendmsg+0x2882/0x2e60 net/ipv6/raw.c:915
inet_sendmsg+0x101/0x180 net/ipv4/af_inet.c:827
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg net/socket.c:734 [inline]
____sys_sendmsg+0xa8e/0xe70 net/socket.c:2476
___sys_sendmsg+0x2a1/0x3f0 net/socket.c:2530
__sys_sendmsg net/socket.c:2559 [inline]
__do_sys_sendmsg net/socket.c:2568 [inline]
__se_sys_sendmsg net/socket.c:2566 [inline]
__x64_sys_sendmsg+0x367/0x540 net/socket.c:2566
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
It is because icmp6hdr does not in skb linear region under the scenario
of SOCK_RAW socket. Access icmp6_hdr(skb)->icmp6_type directly will
trigger the uninit variable access bug.
Use a local variable icmp6_type to carry the correct value in different
scenarios. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/pseries: Rework lppaca_shared_proc() to avoid DEBUG_PREEMPT
lppaca_shared_proc() takes a pointer to the lppaca which is typically
accessed through get_lppaca(). With DEBUG_PREEMPT enabled, this leads
to checking if preemption is enabled, for example:
BUG: using smp_processor_id() in preemptible [00000000] code: grep/10693
caller is lparcfg_data+0x408/0x19a0
CPU: 4 PID: 10693 Comm: grep Not tainted 6.5.0-rc3 #2
Call Trace:
dump_stack_lvl+0x154/0x200 (unreliable)
check_preemption_disabled+0x214/0x220
lparcfg_data+0x408/0x19a0
...
This isn't actually a problem however, as it does not matter which
lppaca is accessed, the shared proc state will be the same.
vcpudispatch_stats_procfs_init() already works around this by disabling
preemption, but the lparcfg code does not, erroring any time
/proc/powerpc/lparcfg is accessed with DEBUG_PREEMPT enabled.
Instead of disabling preemption on the caller side, rework
lppaca_shared_proc() to not take a pointer and instead directly access
the lppaca, bypassing any potential preemption checks.
[mpe: Rework to avoid needing a definition in paca.h and lppaca.h] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915: Fix NULL ptr deref by checking new_crtc_state
intel_atomic_get_new_crtc_state can return NULL, unless crtc state wasn't
obtained previously with intel_atomic_get_crtc_state, so we must check it
for NULLness here, just as in many other places, where we can't guarantee
that intel_atomic_get_crtc_state was called.
We are currently getting NULL ptr deref because of that, so this fix was
confirmed to help.
(cherry picked from commit 1d5b09f8daf859247a1ea65b0d732a24d88980d8) |
| In the Linux kernel, the following vulnerability has been resolved:
devlink: report devlink_port_type_warn source device
devlink_port_type_warn is scheduled for port devlink and warning
when the port type is not set. But from this warning it is not easy
found out which device (driver) has no devlink port set.
[ 3709.975552] Type was not set for devlink port.
[ 3709.975579] WARNING: CPU: 1 PID: 13092 at net/devlink/leftover.c:6775 devlink_port_type_warn+0x11/0x20
[ 3709.993967] Modules linked in: openvswitch nf_conncount nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nfnetlink bluetooth rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache netfs vhost_net vhost vhost_iotlb tap tun bridge stp llc qrtr intel_rapl_msr intel_rapl_common i10nm_edac nfit libnvdimm x86_pkg_temp_thermal mlx5_ib intel_powerclamp coretemp dell_wmi ledtrig_audio sparse_keymap ipmi_ssif kvm_intel ib_uverbs rfkill ib_core video kvm iTCO_wdt acpi_ipmi intel_vsec irqbypass ipmi_si iTCO_vendor_support dcdbas ipmi_devintf mei_me ipmi_msghandler rapl mei intel_cstate isst_if_mmio isst_if_mbox_pci dell_smbios intel_uncore isst_if_common i2c_i801 dell_wmi_descriptor wmi_bmof i2c_smbus intel_pch_thermal pcspkr acpi_power_meter xfs libcrc32c sd_mod sg nvme_tcp mgag200 i2c_algo_bit nvme_fabrics drm_shmem_helper drm_kms_helper nvme syscopyarea ahci sysfillrect sysimgblt nvme_core fb_sys_fops crct10dif_pclmul libahci mlx5_core sfc crc32_pclmul nvme_common drm
[ 3709.994030] crc32c_intel mtd t10_pi mlxfw libata tg3 mdio megaraid_sas psample ghash_clmulni_intel pci_hyperv_intf wmi dm_multipath sunrpc dm_mirror dm_region_hash dm_log dm_mod be2iscsi bnx2i cnic uio cxgb4i cxgb4 tls libcxgbi libcxgb qla4xxx iscsi_boot_sysfs iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi fuse
[ 3710.108431] CPU: 1 PID: 13092 Comm: kworker/1:1 Kdump: loaded Not tainted 5.14.0-319.el9.x86_64 #1
[ 3710.108435] Hardware name: Dell Inc. PowerEdge R750/0PJ80M, BIOS 1.8.2 09/14/2022
[ 3710.108437] Workqueue: events devlink_port_type_warn
[ 3710.108440] RIP: 0010:devlink_port_type_warn+0x11/0x20
[ 3710.108443] Code: 84 76 fe ff ff 48 c7 03 20 0e 1a ad 31 c0 e9 96 fd ff ff 66 0f 1f 44 00 00 0f 1f 44 00 00 48 c7 c7 18 24 4e ad e8 ef 71 62 ff <0f> 0b c3 cc cc cc cc 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 f6 87
[ 3710.108445] RSP: 0018:ff3b6d2e8b3c7e90 EFLAGS: 00010282
[ 3710.108447] RAX: 0000000000000000 RBX: ff366d6580127080 RCX: 0000000000000027
[ 3710.108448] RDX: 0000000000000027 RSI: 00000000ffff86de RDI: ff366d753f41f8c8
[ 3710.108449] RBP: ff366d658ff5a0c0 R08: ff366d753f41f8c0 R09: ff3b6d2e8b3c7e18
[ 3710.108450] R10: 0000000000000001 R11: 0000000000000023 R12: ff366d753f430600
[ 3710.108451] R13: ff366d753f436900 R14: 0000000000000000 R15: ff366d753f436905
[ 3710.108452] FS: 0000000000000000(0000) GS:ff366d753f400000(0000) knlGS:0000000000000000
[ 3710.108453] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 3710.108454] CR2: 00007f1c57bc74e0 CR3: 000000111d26a001 CR4: 0000000000773ee0
[ 3710.108456] PKRU: 55555554
[ 3710.108457] Call Trace:
[ 3710.108458] <TASK>
[ 3710.108459] process_one_work+0x1e2/0x3b0
[ 3710.108466] ? rescuer_thread+0x390/0x390
[ 3710.108468] worker_thread+0x50/0x3a0
[ 3710.108471] ? rescuer_thread+0x390/0x390
[ 3710.108473] kthread+0xdd/0x100
[ 3710.108477] ? kthread_complete_and_exit+0x20/0x20
[ 3710.108479] ret_from_fork+0x1f/0x30
[ 3710.108485] </TASK>
[ 3710.108486] ---[ end trace 1b4b23cd0c65d6a0 ]---
After patch:
[ 402.473064] ice 0000:41:00.0: Type was not set for devlink port.
[ 402.473064] ice 0000:41:00.1: Type was not set for devlink port. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/srpt: Add a check for valid 'mad_agent' pointer
When unregistering MAD agent, srpt module has a non-null check
for 'mad_agent' pointer before invoking ib_unregister_mad_agent().
This check can pass if 'mad_agent' variable holds an error value.
The 'mad_agent' can have an error value for a short window when
srpt_add_one() and srpt_remove_one() is executed simultaneously.
In srpt module, added a valid pointer check for 'sport->mad_agent'
before unregistering MAD agent.
This issue can hit when RoCE driver unregisters ib_device
Stack Trace:
------------
BUG: kernel NULL pointer dereference, address: 000000000000004d
PGD 145003067 P4D 145003067 PUD 2324fe067 PMD 0
Oops: 0002 [#1] PREEMPT SMP NOPTI
CPU: 10 PID: 4459 Comm: kworker/u80:0 Kdump: loaded Tainted: P
Hardware name: Dell Inc. PowerEdge R640/06NR82, BIOS 2.5.4 01/13/2020
Workqueue: bnxt_re bnxt_re_task [bnxt_re]
RIP: 0010:_raw_spin_lock_irqsave+0x19/0x40
Call Trace:
ib_unregister_mad_agent+0x46/0x2f0 [ib_core]
IPv6: ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
? __schedule+0x20b/0x560
srpt_unregister_mad_agent+0x93/0xd0 [ib_srpt]
srpt_remove_one+0x20/0x150 [ib_srpt]
remove_client_context+0x88/0xd0 [ib_core]
bond0: (slave p2p1): link status definitely up, 100000 Mbps full duplex
disable_device+0x8a/0x160 [ib_core]
bond0: active interface up!
? kernfs_name_hash+0x12/0x80
(NULL device *): Bonding Info Received: rdev: 000000006c0b8247
__ib_unregister_device+0x42/0xb0 [ib_core]
(NULL device *): Master: mode: 4 num_slaves:2
ib_unregister_device+0x22/0x30 [ib_core]
(NULL device *): Slave: id: 105069936 name:p2p1 link:0 state:0
bnxt_re_stopqps_and_ib_uninit+0x83/0x90 [bnxt_re]
bnxt_re_alloc_lag+0x12e/0x4e0 [bnxt_re] |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: rcar-host: Pass proper IRQ domain to generic_handle_domain_irq()
Starting with commit dd26c1a23fd5 ("PCI: rcar-host: Switch to
msi_create_parent_irq_domain()"), the MSI parent IRQ domain is NULL because
the object of type struct irq_domain_info passed to:
msi_create_parent_irq_domain() ->
irq_domain_instantiate()() ->
__irq_domain_instantiate()
has no reference to the parent IRQ domain. Using msi->domain->parent as an
argument for generic_handle_domain_irq() leads to below error:
"Unable to handle kernel NULL pointer dereference at virtual address"
This error was identified while switching the upcoming RZ/G3S PCIe host
controller driver to msi_create_parent_irq_domain() (which was using a
similar pattern to handle MSIs (see link section)), but it was not tested
on hardware using the pcie-rcar-host controller driver due to lack of
hardware.
[mani: reworded subject and description] |
| In the Linux kernel, the following vulnerability has been resolved:
net: libwx: fix memory leak in wx_setup_rx_resources
When wx_alloc_page_pool() failed in wx_setup_rx_resources(), it doesn't
release DMA buffer. Add dma_free_coherent() in the error path to release
the DMA buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: raa215300: Fix resource leak in case of error
The clk_register_clkdev() allocates memory by calling vclkdev_alloc() and
this memory is not freed in the error path. Similarly, resources allocated
by clk_register_fixed_rate() are not freed in the error path.
Fix these issues by using devm_clk_hw_register_fixed_rate() and
devm_clk_hw_register_clkdev().
After this, the static variable clk is not needed. Replace it withÂ
local variable hw in probe() and drop calling clk_unregister_fixed_rate()
from raa215300_rtc_unregister_device(). |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: codecs: wcd-mbhc-v2: fix resource leaks on component remove
The MBHC resources must be released on component probe failure and
removal so can not be tied to the lifetime of the component device.
This is specifically needed to allow probe deferrals of the sound card
which otherwise fails when reprobing the codec component:
snd-sc8280xp sound: ASoC: failed to instantiate card -517
genirq: Flags mismatch irq 299. 00002001 (mbhc sw intr) vs. 00002001 (mbhc sw intr)
wcd938x_codec audio-codec: Failed to request mbhc interrupts -16
wcd938x_codec audio-codec: mbhc initialization failed
wcd938x_codec audio-codec: ASoC: error at snd_soc_component_probe on audio-codec: -16
snd-sc8280xp sound: ASoC: failed to instantiate card -16 |
| In the Linux kernel, the following vulnerability has been resolved:
clk: imx93: fix memory leak and missing unwind goto in imx93_clocks_probe
In function probe(), it returns directly without unregistered hws
when error occurs.
Fix this by adding 'goto unregister_hws;' on line 295 and
line 310.
Use devm_kzalloc() instead of kzalloc() to automatically
free the memory using devm_kfree() when error occurs.
Replace of_iomap() with devm_of_iomap() to automatically
handle the unused ioremap region and delete 'iounmap(anatop_base);'
in unregister_hws. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: endpoint: pci-epf-test: Add NULL check for DMA channels before release
The fields dma_chan_tx and dma_chan_rx of the struct pci_epf_test can be
NULL even after EPF initialization. Then it is prudent to check that
they have non-NULL values before releasing the channels. Add the checks
in pci_epf_test_clean_dma_chan().
Without the checks, NULL pointer dereferences happen and they can lead
to a kernel panic in some cases:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000050
Call trace:
dma_release_channel+0x2c/0x120 (P)
pci_epf_test_epc_deinit+0x94/0xc0 [pci_epf_test]
pci_epc_deinit_notify+0x74/0xc0
tegra_pcie_ep_pex_rst_irq+0x250/0x5d8
irq_thread_fn+0x34/0xb8
irq_thread+0x18c/0x2e8
kthread+0x14c/0x210
ret_from_fork+0x10/0x20
[mani: trimmed the stack trace] |
| In the Linux kernel, the following vulnerability has been resolved:
posix-timers: Prevent RT livelock in itimer_delete()
itimer_delete() has a retry loop when the timer is concurrently expired. On
non-RT kernels this just spin-waits until the timer callback has completed,
except for posix CPU timers which have HAVE_POSIX_CPU_TIMERS_TASK_WORK
enabled.
In that case and on RT kernels the existing task could live lock when
preempting the task which does the timer delivery.
Replace spin_unlock() with an invocation of timer_wait_running() to handle
it the same way as the other retry loops in the posix timer code. |
| In the Linux kernel, the following vulnerability has been resolved:
block: fix blktrace debugfs entries leakage
Commit 99d055b4fd4b ("block: remove per-disk debugfs files in
blk_unregister_queue") moves blk_trace_shutdown() from
blk_release_queue() to blk_unregister_queue(), this is safe if blktrace
is created through sysfs, however, there is a regression in corner
case.
blktrace can still be enabled after del_gendisk() through ioctl if
the disk is opened before del_gendisk(), and if blktrace is not shutdown
through ioctl before closing the disk, debugfs entries will be leaked.
Fix this problem by shutdown blktrace in disk_release(), this is safe
because blk_trace_remove() is reentrant. |
| In the Linux kernel, the following vulnerability has been resolved:
netlink: annotate accesses to nlk->cb_running
Both netlink_recvmsg() and netlink_native_seq_show() read
nlk->cb_running locklessly. Use READ_ONCE() there.
Add corresponding WRITE_ONCE() to netlink_dump() and
__netlink_dump_start()
syzbot reported:
BUG: KCSAN: data-race in __netlink_dump_start / netlink_recvmsg
write to 0xffff88813ea4db59 of 1 bytes by task 28219 on cpu 0:
__netlink_dump_start+0x3af/0x4d0 net/netlink/af_netlink.c:2399
netlink_dump_start include/linux/netlink.h:308 [inline]
rtnetlink_rcv_msg+0x70f/0x8c0 net/core/rtnetlink.c:6130
netlink_rcv_skb+0x126/0x220 net/netlink/af_netlink.c:2577
rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:6192
netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline]
netlink_unicast+0x56f/0x640 net/netlink/af_netlink.c:1365
netlink_sendmsg+0x665/0x770 net/netlink/af_netlink.c:1942
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg net/socket.c:747 [inline]
sock_write_iter+0x1aa/0x230 net/socket.c:1138
call_write_iter include/linux/fs.h:1851 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x463/0x760 fs/read_write.c:584
ksys_write+0xeb/0x1a0 fs/read_write.c:637
__do_sys_write fs/read_write.c:649 [inline]
__se_sys_write fs/read_write.c:646 [inline]
__x64_sys_write+0x42/0x50 fs/read_write.c:646
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
read to 0xffff88813ea4db59 of 1 bytes by task 28222 on cpu 1:
netlink_recvmsg+0x3b4/0x730 net/netlink/af_netlink.c:2022
sock_recvmsg_nosec+0x4c/0x80 net/socket.c:1017
____sys_recvmsg+0x2db/0x310 net/socket.c:2718
___sys_recvmsg net/socket.c:2762 [inline]
do_recvmmsg+0x2e5/0x710 net/socket.c:2856
__sys_recvmmsg net/socket.c:2935 [inline]
__do_sys_recvmmsg net/socket.c:2958 [inline]
__se_sys_recvmmsg net/socket.c:2951 [inline]
__x64_sys_recvmmsg+0xe2/0x160 net/socket.c:2951
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
value changed: 0x00 -> 0x01 |
| In the Linux kernel, the following vulnerability has been resolved:
s390/vmem: split pages when debug pagealloc is enabled
Since commit bb1520d581a3 ("s390/mm: start kernel with DAT enabled")
the kernel crashes early during boot when debug pagealloc is enabled:
mem auto-init: stack:off, heap alloc:off, heap free:off
addressing exception: 0005 ilc:2 [#1] SMP DEBUG_PAGEALLOC
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 6.5.0-rc3-09759-gc5666c912155 #630
[..]
Krnl Code: 00000000001325f6: ec5600248064 cgrj %r5,%r6,8,000000000013263e
00000000001325fc: eb880002000c srlg %r8,%r8,2
#0000000000132602: b2210051 ipte %r5,%r1,%r0,0
>0000000000132606: b90400d1 lgr %r13,%r1
000000000013260a: 41605008 la %r6,8(%r5)
000000000013260e: a7db1000 aghi %r13,4096
0000000000132612: b221006d ipte %r6,%r13,%r0,0
0000000000132616: e3d0d0000171 lay %r13,4096(%r13)
Call Trace:
__kernel_map_pages+0x14e/0x320
__free_pages_ok+0x23a/0x5a8)
free_low_memory_core_early+0x214/0x2c8
memblock_free_all+0x28/0x58
mem_init+0xb6/0x228
mm_core_init+0xb6/0x3b0
start_kernel+0x1d2/0x5a8
startup_continue+0x36/0x40
Kernel panic - not syncing: Fatal exception: panic_on_oops
This is caused by using large mappings on machines with EDAT1/EDAT2. Add
the code to split the mappings into 4k pages if debug pagealloc is enabled
by CONFIG_DEBUG_PAGEALLOC_ENABLE_DEFAULT or the debug_pagealloc kernel
command line option. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: serial: imx: disable Ageing Timer interrupt request irq
There maybe pending USR interrupt before requesting irq, however
uart_add_one_port has not executed, so there will be kernel panic:
[ 0.795668] Unable to handle kernel NULL pointer dereference at virtual addre
ss 0000000000000080
[ 0.802701] Mem abort info:
[ 0.805367] ESR = 0x0000000096000004
[ 0.808950] EC = 0x25: DABT (current EL), IL = 32 bits
[ 0.814033] SET = 0, FnV = 0
[ 0.816950] EA = 0, S1PTW = 0
[ 0.819950] FSC = 0x04: level 0 translation fault
[ 0.824617] Data abort info:
[ 0.827367] ISV = 0, ISS = 0x00000004
[ 0.831033] CM = 0, WnR = 0
[ 0.833866] [0000000000000080] user address but active_mm is swapper
[ 0.839951] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
[ 0.845953] Modules linked in:
[ 0.848869] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.1.1+g56321e101aca #1
[ 0.855617] Hardware name: Freescale i.MX8MP EVK (DT)
[ 0.860452] pstate: 000000c5 (nzcv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 0.867117] pc : __imx_uart_rxint.constprop.0+0x11c/0x2c0
[ 0.872283] lr : imx_uart_int+0xf8/0x1ec
The issue only happends in the inmate linux when Jailhouse hypervisor
enabled. The test procedure is:
while true; do
jailhouse enable imx8mp.cell
jailhouse cell linux xxxx
sleep 10
jailhouse cell destroy 1
jailhouse disable
sleep 5
done
And during the upper test, press keys to the 2nd linux console.
When `jailhouse cell destroy 1`, the 2nd linux has no chance to put
the uart to a quiese state, so USR1/2 may has pending interrupts. Then
when `jailhosue cell linux xx` to start 2nd linux again, the issue
trigger.
In order to disable irqs before requesting them, both UCR1 and UCR2 irqs
should be disabled, so here fix that, disable the Ageing Timer interrupt
in UCR2 as UCR1 does. |
| In the Linux kernel, the following vulnerability has been resolved:
bcache: fixup btree_cache_wait list damage
We get a kernel crash about "list_add corruption. next->prev should be
prev (ffff9c801bc01210), but was ffff9c77b688237c.
(next=ffffae586d8afe68)."
crash> struct list_head 0xffff9c801bc01210
struct list_head {
next = 0xffffae586d8afe68,
prev = 0xffffae586d8afe68
}
crash> struct list_head 0xffff9c77b688237c
struct list_head {
next = 0x0,
prev = 0x0
}
crash> struct list_head 0xffffae586d8afe68
struct list_head struct: invalid kernel virtual address: ffffae586d8afe68 type: "gdb_readmem_callback"
Cannot access memory at address 0xffffae586d8afe68
[230469.019492] Call Trace:
[230469.032041] prepare_to_wait+0x8a/0xb0
[230469.044363] ? bch_btree_keys_free+0x6c/0xc0 [escache]
[230469.056533] mca_cannibalize_lock+0x72/0x90 [escache]
[230469.068788] mca_alloc+0x2ae/0x450 [escache]
[230469.080790] bch_btree_node_get+0x136/0x2d0 [escache]
[230469.092681] bch_btree_check_thread+0x1e1/0x260 [escache]
[230469.104382] ? finish_wait+0x80/0x80
[230469.115884] ? bch_btree_check_recurse+0x1a0/0x1a0 [escache]
[230469.127259] kthread+0x112/0x130
[230469.138448] ? kthread_flush_work_fn+0x10/0x10
[230469.149477] ret_from_fork+0x35/0x40
bch_btree_check_thread() and bch_dirty_init_thread() may call
mca_cannibalize() to cannibalize other cached btree nodes. Only one thread
can do it at a time, so the op of other threads will be added to the
btree_cache_wait list.
We must call finish_wait() to remove op from btree_cache_wait before free
it's memory address. Otherwise, the list will be damaged. Also should call
bch_cannibalize_unlock() to release the btree_cache_alloc_lock and wake_up
other waiters. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/irdma: Fix data race on CQP completion stats
CQP completion statistics is read lockesly in irdma_wait_event and
irdma_check_cqp_progress while it can be updated in the completion
thread irdma_sc_ccq_get_cqe_info on another CPU as KCSAN reports.
Make completion statistics an atomic variable to reflect coherent updates
to it. This will also avoid load/store tearing logic bug potentially
possible by compiler optimizations.
[77346.170861] BUG: KCSAN: data-race in irdma_handle_cqp_op [irdma] / irdma_sc_ccq_get_cqe_info [irdma]
[77346.171383] write to 0xffff8a3250b108e0 of 8 bytes by task 9544 on cpu 4:
[77346.171483] irdma_sc_ccq_get_cqe_info+0x27a/0x370 [irdma]
[77346.171658] irdma_cqp_ce_handler+0x164/0x270 [irdma]
[77346.171835] cqp_compl_worker+0x1b/0x20 [irdma]
[77346.172009] process_one_work+0x4d1/0xa40
[77346.172024] worker_thread+0x319/0x700
[77346.172037] kthread+0x180/0x1b0
[77346.172054] ret_from_fork+0x22/0x30
[77346.172136] read to 0xffff8a3250b108e0 of 8 bytes by task 9838 on cpu 2:
[77346.172234] irdma_handle_cqp_op+0xf4/0x4b0 [irdma]
[77346.172413] irdma_cqp_aeq_cmd+0x75/0xa0 [irdma]
[77346.172592] irdma_create_aeq+0x390/0x45a [irdma]
[77346.172769] irdma_rt_init_hw.cold+0x212/0x85d [irdma]
[77346.172944] irdma_probe+0x54f/0x620 [irdma]
[77346.173122] auxiliary_bus_probe+0x66/0xa0
[77346.173137] really_probe+0x140/0x540
[77346.173154] __driver_probe_device+0xc7/0x220
[77346.173173] driver_probe_device+0x5f/0x140
[77346.173190] __driver_attach+0xf0/0x2c0
[77346.173208] bus_for_each_dev+0xa8/0xf0
[77346.173225] driver_attach+0x29/0x30
[77346.173240] bus_add_driver+0x29c/0x2f0
[77346.173255] driver_register+0x10f/0x1a0
[77346.173272] __auxiliary_driver_register+0xbc/0x140
[77346.173287] irdma_init_module+0x55/0x1000 [irdma]
[77346.173460] do_one_initcall+0x7d/0x410
[77346.173475] do_init_module+0x81/0x2c0
[77346.173491] load_module+0x1232/0x12c0
[77346.173506] __do_sys_finit_module+0x101/0x180
[77346.173522] __x64_sys_finit_module+0x3c/0x50
[77346.173538] do_syscall_64+0x39/0x90
[77346.173553] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[77346.173634] value changed: 0x0000000000000094 -> 0x0000000000000095 |
