| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ad_sigma_delta: fix CS held asserted and state leaks
In ad_sigma_delta_single_conversion(), set_mode(AD_SD_MODE_IDLE) and
disable_one() were called from the out: block while keep_cs_asserted
was still true. This caused any SPI transfer issued by those callbacks
to carry cs_change=1, leaving CS permanently asserted after the
conversion. Fix by moving both calls into the out_unlock: block, after
keep_cs_asserted is cleared, matching the pattern already used in
ad_sd_calibrate().
In the error path of ad_sd_buffer_postenable(), if an operation fails
after set_mode(AD_SD_MODE_CONTINUOUS) has already succeeded (e.g.
spi_offload_trigger_enable()), the device is left in continuous
conversion mode with CS physically asserted. Additionally,
bus_locked remaining true after spi_bus_unlock() causes subsequent
SPI operations to call spi_sync_locked() without the bus lock actually
held, allowing concurrent SPI access.
Fix the error path by clearing keep_cs_asserted first, then calling
set_mode(AD_SD_MODE_IDLE) to revert the device mode and deassert CS,
then clearing bus_locked before releasing the bus.
For devices that implement neither set_mode nor disable_one (such as
MAX11205, which has no physical CS pin), no SPI transfer is issued
during cleanup and the cs_change flag has no effect on any physical
line. |
| In NLnet Labs Unbound 1.20.0 up to and including 1.25.1, when Unbound is configured with 'serve-expired: yes' and 'serve-expired-client-timeout > discard-timeout > 0' (contrary to the suggested values), the discard-timeout branch during the serve expired logic drops an aged client reply without performing the correct accounting for the number of reply addresses for the query. Other identical branches outside of serve expired perform the correct decrement. Since the counter is never decremented in such scenario, it can reach the maximum limit and new clients for duplicate in-flight queries are silently dropped resulting in degradation of resolution service. A malicious actor can exploit the vulnerability by querying the resolver for a client-controlled slow-on-demand authoritative zone that can drive the counter past the threshold. Shipped defaults for 'serve-expired-client-timeout: 1800' and 'discard-timeout: 1900' make the branch unreachable. |
| In the Linux kernel, the following vulnerability has been resolved:
espintcp: fix skb leaks
A few error paths are missing a kfree_skb. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: Fix vport QoS cleanup on error
When enabling vport QoS fails, the scheduling node was never freed,
causing a leak.
Add the missing free and reset the vport scheduling node pointer to
NULL. |
| dhcpcd through 10.3.2, fixed in commit 708b4a5, contains a memory leak vulnerability in the IPv6 Router Advertisement route information handling that allows an unauthenticated same-link attacker to cause denial of service by sending crafted Router Advertisements. Attackers can repeatedly send Router Advertisements containing Route Information options with a lifetime of zero, triggering unfreed allocations in routeinfo_findalloc() that cause linear memory exhaustion and eventual daemon crash. |
| In NLnet Labs Unbound 1.22.0 up to and including 1.25.1, client terminated DNS-over-QUIC (DoQ) queries are not accounted properly by Unbound resulting in low-cost inflation of the waiting number of replies for already in-flight resolution queries. This results in degradation of resolution service for new clients for already in-flight queries. A malicious actor can exploit the vulnerability by issuing DoQ queries for query names that need resolution and proceeding on immediately terminating the query by one of STOP_SENDING/RESET_STREAM/CONNECTION_CLOSE QUIC frames. Those terminated DoQ queries are not properly counted for and keep inflating the number of waiting replies for in-flight queries. When the maximum is reached, it results in silent query drops for new clients needing resolution for already in-flight queries. This vulnerability needs Unbound to be compiled with DoQ support ('--with-libngtcp2') and the 'quic-port' to be configured for the listening interfaces. Additionally, a malicious actor needs access to multiple source IPs to bypass the by-default configured 'wait-limit' option. |
| Netty is a network application framework for development of protocol servers and clients. In versions 4.2.0.Final through 4.2.15.Final and 4.1.0.Final through 4.1.135.Final, the `SpdyHttpDecoder` handler in Netty's SPDY-to-HTTP codec allocates a pooled `ByteBuf` when processing a client-initiated `SYN_STREAM` frame with `FLAG_FIN=0` and stores the partially constructed `FullHttpRequest` in `messageMap`; when the remote peer sends `RST_STREAM` for that stream or the accumulated content exceeds `maxContentLength`, the decoder removes the entry but does not release the pooled `ByteBuf`, causing native memory exhaustion. This issue is fixed in versions 4.1.136.Final and 4.2.16.Final. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ti-ads1119: fix PM reference leak in buffer preenable
ads1119_triggered_buffer_preenable() resumes the device with
pm_runtime_resume_and_get() before starting a conversion.
If i2c_smbus_write_byte() fails, the function returns the error directly
and leaves the runtime PM usage counter elevated. The matching
postdisable callback is not called when preenable fails, so the reference
is leaked and the device may remain runtime-active indefinitely.
Store the I2C transfer result in ret and drop the runtime PM reference on
failure before returning the error. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: accel: kxsd9: fix runtime PM imbalance on write_raw() error
kxsd9_write_raw() takes a runtime PM reference with pm_runtime_get_sync()
but returns -EINVAL directly when a scale with a non-zero integer part is
requested, skipping the matching pm_runtime_put_autosuspend(). This leaks
a runtime PM usage-counter reference on every such write, after which the
device can no longer autosuspend.
Set the error code and fall through to the existing put instead of
returning early. |
| In the Linux kernel, the following vulnerability has been resolved:
rust: block: fix GenDisk cleanup paths
GenDiskBuilder::build() still has fallible work after
__blk_mq_alloc_disk(), but its error path only recovers the
foreign queue data. That leaks the temporary gendisk and
request_queue until later teardown. If the caller moved the last
Arc<TagSet<T>> into build(), the leaked queue can retain blk-mq
state after the tag set is dropped.
Fix the pre-registration failure path by dropping the temporary
gendisk reference with put_disk() before recovering queue_data,
so disk_release() can tear down the owned queue.
Also pair GenDisk::drop() with put_disk() after del_gendisk().
Once a Rust GenDisk has been added with device_add_disk(),
del_gendisk() only unregisters it; the final gendisk reference
still has to be dropped to complete the release path. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: buffer: hw-consumer: free scan_mask on buffer release
The scan_mask lifetime changed in commit 9a2e1233d38c ("iio: buffer:
hw-consumer: remove redundant scan_mask flexible array").
Before that change, the scan mask storage was embedded in struct
hw_consumer_buffer, so iio_hw_buf_release() could free the whole
allocation with a single kfree(hw_buf).
That commit moved the scan mask to a separate bitmap_zalloc() allocation
stored in buffer.scan_mask, but left iio_hw_buf_release() unchanged.
Free the scan mask in iio_hw_buf_release() before freeing the buffer
wrapper. |
| In the Linux kernel, the following vulnerability has been resolved:
xhci: sideband: fix ring sg table pages leak
xhci_ring_to_sgtable() allocates a temporary pages array and
uses it to build the returned sg_table with
sg_alloc_table_from_pages().
The error paths free the pages array, but the success path
returns the sg_table without freeing it. This leaks the temporary
array every time a sideband client gets an endpoint or event ring
buffer.
Free the pages array after sg_alloc_table_from_pages() succeeds.
The returned sg_table has its own scatterlist entries and does not
depend on the temporary array after construction. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix mechToken leak when SPNEGO decode fails after token alloc
The kernel ASN.1 BER decoder calls action callbacks incrementally as it
walks the input. When ksmbd_decode_negTokenInit() reaches the mechToken
[2] OCTET STRING element, ksmbd_neg_token_alloc() allocates
conn->mechToken immediately via kmemdup_nul(). If a later element in
the same blob is malformed, then the decoder will return nonzero after
the allocation is already live. This could happen if mechListMIC [3]
overrunse the enclosing SEQUENCE.
decode_negotiation_token() then sets conn->use_spnego = false because
both the negTokenInit and negTokenTarg grammars failed. The cleanup at
the bottom of smb2_sess_setup() is gated on use_spnego:
if (conn->use_spnego && conn->mechToken) {
kfree(conn->mechToken);
conn->mechToken = NULL;
}
so the kfree is skipped, causing the mechToken to never be freed.
This codepath is reachable pre-authentication, so untrusted clients can
cause slow memory leaks on a server without even being properly
authenticated.
Fix this up by not checking check for use_spnego, as it's not required,
so the memory will always be properly freed. At the same time, always
free the memory in ksmbd_conn_free() incase some other failure path
forgot to free it. |
| Sandbox escape due to use-after-free in the Disability Access APIs component. This vulnerability was fixed in Firefox 153, Firefox ESR 115.38, Firefox ESR 140.13, Thunderbird 153, and Thunderbird 140.13. |
| In the Linux kernel, the following vulnerability has been resolved:
nfsd: fix posix_acl leak on SETACL decode failure
nfsaclsvc_decode_setaclargs() and nfs3svc_decode_setaclargs() each
call nfs_stream_decode_acl() twice, first for NFS_ACL and then for
NFS_DFACL. Each successful call transfers ownership of a freshly
allocated posix_acl into argp->acl_access or argp->acl_default. If
the first call succeeds but the second fails, the decoder returns
false and argp->acl_access is left dangling.
ACLPROC2_SETACL.pc_release was wired to nfssvc_release_attrstat and
ACLPROC3_SETACL.pc_release was wired to nfs3svc_release_fhandle.
Both only call fh_put() and have no knowledge of the ACL fields on
argp. The posix_acl_release() pairs sat at the out: labels inside
nfsacld_proc_setacl() and nfsd3_proc_setacl(), but svc_process()
skips pc_func when pc_decode returns false, so that cleanup is
unreachable on decode failure:
svc_process_common()
pc_decode() /* decode_setaclargs: false */
/* pc_func skipped */
pc_release() /* fh_put only -- ACLs leaked */
The orphaned posix_acl is leaked for the lifetime of the server.
Fix by adding nfsaclsvc_release_setacl() and nfs3svc_release_setacl(),
which release both argp->acl_access and argp->acl_default in addition
to fh_put(), and wiring them as pc_release for their respective SETACL
procedures. pc_release runs on every path svc_process() takes after
decode, including decode failure, so the posix_acl_release() pairs are
removed from the proc functions' out: labels to keep ownership in one
place. This matches the existing release_getacl() pattern used by
the sibling GETACL procedures. |
| In the Linux kernel, the following vulnerability has been resolved:
nfsd: fix posix_acl leak and ignored error in nfsd4_create_file
nfsd4_create_file() has two bugs in its ACL handling:
The return value of nfsd4_acl_to_attr() is silently discarded. When
the NFSv4-to-POSIX ACL conversion fails (e.g., -EINVAL for
unsupported ACE types), the file is created without any ACL and the
client receives NFS4_OK. This violates RFC 7530/8881 which require
the server to reject unsupported attributes on CREATE.
When start_creating() fails after ACL attributes have been populated
in attrs (either via nfsd4_acl_to_attr or via ownership transfer from
open->op_dpacl/op_pacl), the function jumps to out_write which skips
nfsd_attrs_free(). The posix_acl allocations are leaked. A client
can trigger this repeatedly with OPEN(CREATE), ACL attributes, and an
invalid filename (e.g., longer than NAME_MAX).
Fix both by capturing the nfsd4_acl_to_attr() return value and by
changing the early error paths to jump to out instead of out_write.
Initialize child to ERR_PTR(-EINVAL) so that end_creating() is safe
to call even if start_creating() was never reached. |
| In the Linux kernel, the following vulnerability has been resolved:
nfsd: fix dead ACL conflict guard in nfsd4_create
nfsd4_create() steals create->cr_dpacl/cr_pacl into the local
nfsd_attrs via the designated initializer, then immediately sets the
source pointers to NULL. The subsequent conflict guard tests the
already-nilled source fields, making it permanently dead code:
if (create->cr_acl) {
if (create->cr_dpacl || create->cr_pacl) /* always false */
When a client encodes both FATTR4_WORD0_ACL and
FATTR4_WORD2_POSIX_{DEFAULT,ACCESS}_ACL in the same CREATE fattr
bitmap, nfsd4_acl_to_attr() overwrites attrs.na_pacl/na_dpacl without
releasing the originals, leaking two posix_acl slab objects per
request. Repeated requests cause unbounded slab exhaustion.
Fix by checking attrs.na_dpacl/na_pacl (the stolen values) instead of
the nilled create->cr_dpacl/cr_pacl, matching the correct pattern
already used in nfsd4_setattr(). |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: v: prevent OGM aggregation on disabled hardif
When an interface gets disabled, the worker is correctly disabled by
batadv_hardif_disable_interface() -> ... -> batadv_v_ogm_iface_disable().
In this process, the skb aggr_list is also freed.
But batadv_v_ogm_send_meshif() can still queue new skbs (via
batadv_v_ogm_queue_on_if()) to the aggr_list. This will only stop after all
cores can no longer find the RCU protected list of hard interfaces. These
queued skbs will never be freed or consumed by batadv_v_ogm_aggr_work.
The batadv_v_ogm_iface_disable() function must block
batadv_v_ogm_queue_on_if() to avoid leak of skbs. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: usb: fix memory leaks on USB write failures
When rtw_usb_write_port() fails to submit a USB Request Block (URB)
(e.g., due to device disconnect or ENOMEM), the completion callback is
never executed.
Currently, the driver ignores the return value of rtw_usb_write_port()
in rtw_usb_write_data() and rtw_usb_tx_agg_skb(). Because these
functions rely on the completion callback to free the socket buffers
(skbs) and the transaction control block (txcb), a submission failure
results in:
1. A memory leak of the allocated skb in rtw_usb_write_data().
2. A memory leak of the txcb structure and all aggregated skbs in
rtw_usb_tx_agg_skb().
Fix this by checking the return value of rtw_usb_write_port(). If it
fails, explicitly free the skb in rtw_usb_write_data(), and properly
purge the tx_ack_queue and free the txcb in rtw_usb_tx_agg_skb().
The issue was discovered in practice during device disconnect/reconnect
scenarios and memory pressure conditions. Tested by verifying normal TX
operation continues after the fix without regressions. |
| In the Linux kernel, the following vulnerability has been resolved:
irqchip/imgpdc: Fix resource leak, add missing chained handler cleanup on remove
The driver allocates domain generic chips using
irq_alloc_domain_generic_chips() during probe and sets up chained
handlers using irq_set_chained_handler_and_data(). However, on driver
removal, the generic chips are not freed and the chained handlers are
not removed.
The generic chips remain on the global gc_list and may later be accessed by
generic interrupt chip suspend, resume, or shutdown callbacks after the
driver has been removed, potentially resulting in a use-after-free and
kernel crash.
The chained handlers that were installed in probe for peripheral and
syswake interrupts are also left dangling, which can lead to spurious
interrupts accessing freed memory.
Fix these issues by:
- Setting IRQ_DOMAIN_FLAG_DESTROY_GC flag in domain->flags, so the
core code automatically removes generic chips when irq_domain_remove()
is called
- Clearing all chained handlers with NULL in pdc_intc_remove() |
