| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
vfio/qat: fix f_pos race in qat_vf_resume_write()
qat_vf_resume_write() checks filp->f_pos before taking migf->lock, but
copies into the migration-state buffer after taking the lock and
re-reading the shared file position.
Two concurrent writers could therefore pass the bounds check with the
old offset, then have the second writer copy after the first advanced
f_pos, writing past the end of the migration-state buffer.
Take migf->lock before doing the boundary checks. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: cttimeout: detach dataplane timeout policy and repurpose refcount
Add a refcount for struct nf_ct_timeout which is used by ct extension to
set the custom ct timeout policy, this tells us that the ct timeout is
being used by a conntrack entry. When the last conntrack entry drops the
refcount on the ct timeout, the ct timeout is released.
Remove the refcount for control plane which controls if the ruleset
refers to the timeout policy. After this update, it is possible to
remove the ct timeout policy from nfnetlink_cttimeout immediately.
This is for simplicity not to handle two refcounts on a single object.
Remove nf_queue_nf_hook_drop(): a packet sitting in nfqueue will just
hold a reference to the nf_ct_timeout object until packet is reinjected,
since this is part of the ct extension, this will be released by the
time the conntrack is freed.
nf_ct_untimeout() is still called to clean up in a best effort basis:
the ct timeout on existing entries gets removed when the ct timeout goes
away, but as long as the iptables ruleset still refers to the ct timeout
through a template, new conntracks may keep attaching it and extend its
lifetime until the rule is removed.
nf_ct_untimeout() is not called anymore from module removal path, this
is unlikely to find timeouts give module refcount is bumped, and the new
refcount already tracks the ct timeout policy use so it is released when
unused. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: tegra: tegra210_ahub: Validate written enum value
tegra_ahub_put_value_enum() reads e->values[item[0]] before
checking whether item[0] is within the enum item range. The existing
check therefore happens too late to prevent an out-of-range read of the
values array.
Move the check before the array access. |
| In the Linux kernel, the following vulnerability has been resolved:
vhost/vdpa: validate virtqueue index in mmap and fault paths
vhost_vdpa_mmap() and vhost_vdpa_fault() use vma->vm_pgoff as a
virtqueue index for get_vq_notification(), but they do not validate
that the index is smaller than v->nvqs.
The ioctl path already performs both a bounds check and
array_index_nospec(), but the mmap/fault path only checks that the
index fits in u16. This allows an out-of-range queue index to reach
driver-specific get_vq_notification() callbacks.
Fix this by extracting a unified vhost_vdpa_get_vq_notification()
helper that validates the queue index against v->nvqs and applies
array_index_nospec() before calling the driver callback. Both the
mmap and fault paths use this helper, and the bounds checking is
consolidated into a single location.
From source inspection, the most defensible impact is out-of-bounds
access in the callback path, potentially leading to invalid PFN
remaps and crash/DoS. |
| In the Linux kernel, the following vulnerability has been resolved:
vduse: hold vduse_lock across IDR lookup in open path
vduse_dev_open() looks up struct vduse_dev through the IDR and then
acquires dev->lock only after vduse_lock has been dropped.
This leaves a window where a concurrent VDUSE_DESTROY_DEV can remove the
same object from the IDR and free it before the open path locks the
device, leading to a use-after-free.
Close this race by keeping vduse_lock held until dev->lock has been
acquired in the open path, matching the lock ordering already used by
the destroy path. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Cancel special fields on map value recycle
Map update and delete paths currently call bpf_obj_free_fields() when a
value is being replaced or recycled. That makes field destruction depend
on the context of the update/delete operation. For tracing programs this
can include NMI context, where referenced kptr destructors, uptr
unpinning, and graph root destruction are not generally safe.
Introduce bpf_obj_cancel_fields() for the reusable-value path. It only
performs NMI-safe cleanup for timer, workqueue, and task_work fields.
Fields that need full destruction are left attached to the recycled value
and are destroyed by the final cleanup path instead.
Switch array and hashtab update/delete/recycle paths to this cancel
helper. Keep bpf_obj_free_fields() for final map destruction and for
bpf_mem_alloc destructors. Preallocated hashtabs do not have allocator
destructors, so teardown continues to walk the normal and extra elements
and fully destroy their fields.
This deliberately relaxes the eager-free semantics of map update/delete
for special fields. Programs that relied on a recycled map slot becoming
empty immediately after update/delete were relying on behavior that
cannot be implemented safely from every BPF execution context without
offloading arbitrary destructors.
There is a chance this change breaks programs making assumptions
regarding the eager freeing of fields. If so, we can relax semantics to
cancellation only when irqs_disabled() is true in the future. However,
theoretically, map values that get reused eagerly already have weaker
guarantees as parallel users can recreate freed fields before the new
element becomes visible again. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: Handle layout stid in nfsd4_drop_revoked_stid()
nfsd4_drop_revoked_stid() has no SC_TYPE_LAYOUT case, so when a
client sends FREE_STATEID for an admin-revoked layout stid, the
default branch releases cl_lock and returns without unhashing or
releasing the stid. The stid remains in the IDR and on the
per-client list until the client is destroyed.
Remove the layout stid from the per-client list and call
nfs4_put_stid() to drop the creation reference. When the
refcount reaches zero, nfsd4_free_layout_stateid() handles the
remaining cleanup: cancelling the fence worker, removing from
the per-file list, and freeing the slab object. |
| In the Linux kernel, the following vulnerability has been resolved:
iommufd: Destroy the pages content after detaching from dmabuf
Sashiko points out this has gotten out of order, the mutex could still be
in use through the dmabuf invalidation callbacks. Don't destroy any of the
pages content until the dmabuf is fully detached. |
| Berkeley Out-of-Order Machine (BOOM) commit 5223e44cfeb26f41380057a2eb4d651197475f69 contains a potential incorrect privilege assignment issue in the v3 and v4 NBDTLB implementations. The raw mstatus.SUM value participates in the read and write permission logic without an explicit local satp.MODE validity check at the use site |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2: reject FITRIM ranges shorter than a cluster
ocfs2_trim_mainbm() trims the global bitmap in cluster units, but its
too-short range validation only checks sb->s_blocksize.
On filesystems with a cluster size larger than the block size, a FITRIM
range that is at least one block but shorter than one cluster is accepted
and shifted down to len == 0. The later start + len - 1 and len -= ...
arithmetic then underflows and can drive trimming past the requested
range.
Reject ranges shorter than s_clustersize instead. That preserves the
existing -EINVAL behavior for requests that cannot discard even one
allocation unit and keeps zero-cluster trims out of the group walk. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Take mmap_lock in zap_pages()
zap_vma_range() requires the owning mm's mmap_lock to be held.
Taking mmap_read_lock under arena->lock would AB-BA against
arena_vm_close() and arena_map_mmap(), both of which run with
mmap_write_lock held and then acquire arena->lock. Instead drop
arena->lock, mmget_not_zero() the vma's mm, take mmap_read_lock, and
re-resolve the vma via find_vma() since it may have been unmapped or
replaced while waiting.
Track processed vmls with a per-call generation in vml->zap_gen and
serialize zap_pages() callers with a new arena->zap_mutex so
concurrent callers on different uaddr ranges do not mark each other's
vmls processed before the zap is done. |
| In the Linux kernel, the following vulnerability has been resolved:
vhost: fix vhost_get_avail_idx for a non empty ring
vhost_get_avail_idx is supposed to report whether it has updated
vq->avail_idx. Instead, it returns whether all entries have been
consumed, which is usually the same. But not always - in
drivers/vhost/net.c and when mergeable buffers have been enabled, the
driver checks whether the combined entries are big enough to store an
incoming packet. If not, the driver re-enables notifications with
available entries still in the ring. The incorrect return value from
vhost_get_avail_idx propagates through vhost_enable_notify and causes
the host to livelock if the guest is not making progress, as vhost will
immediately disable notifications and retry using the available entries.
This goes back to commit d3bb267bbdcb ("vhost: cache avail index in
vhost_enable_notify()") which changed vhost_enable_notify() to compare
the freshly read avail index against vq->last_avail_idx instead of the
previously cached vq->avail_idx. Commit 7ad472397667 ("vhost: move
smp_rmb() into vhost_get_avail_idx()") then carried over the same
comparison when refactoring vhost_enable_notify() to call the unified
vhost_get_avail_idx().
The obvious fix is to make vhost_get_avail_idx do what the comment
says it does and report whether new entries have been added. |
| In the Linux kernel, the following vulnerability has been resolved:
configfs_lookup(): don't leave ->s_dentry dangling on failure
Normally ->s_dentry is cleared when dentry it's pointing to becomes
negative (on eviction, realistically). However, that only happens
if dentry gets to be positive in the first place; in case of inode
allocation failure dentry never becomes positive, so ->d_iput()
is not called at all.
We do part of what normally would've been done by configfs_d_iput()
(dropping the reference to configfs_dirent) manually, but we do
not clear ->s_dentry there. Sloppy as it is, it does not matter in
case of configfs_create_{dir,link}() - there configfs_dirent does
not survive dropping the sole reference to it.
However, for configfs_lookup() it *does* survive, with a dangling
pointer to soon to be freed dentry sitting it its ->s_dentry.
Subsequent getdents(2) in that directory will end up dereferencing
that pointer in order to pick the inode number. Use after free...
This is the minimal fix; the right approach is to set the linkage
between dentry and configfs_dirent only after we know that we have
an inode, but that takes more surgery and the bug had been there
since 2006, so... |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: fix UAF by restoring RCU-delayed inode freeing in bpffs
commit 4f375ade6aa9 ("bpf: Avoid RCU context warning when unpinning
htab with internal structs") moved inode cleanup from ->free_inode()
into ->destroy_inode() to avoid sleeping in RCU context when calling
bpf_any_put(). However this removed the RCU delay on freeing the
inode itself and the cached symlink body (i_link), both of which
can be accessed by RCU pathwalk (pick_link, may_lookup etc.).
This causes a use-after-free when a concurrent unlinkat() drops the
last inode reference and destroy_inode() frees the inode immediately,
while another task is still walking the path in RCU mode and reads
inode->i_opflags (offset +2) inside current_time() -> is_mgtime().
KASAN reports:
BUG: KASAN: slab-use-after-free in is_mgtime include/linux/fs.h:2313
Read of size 2 at addr ffff8880407e4282 (offset +2 = i_opflags)
The rules (per Al Viro):
->destroy_inode() called immediately, can sleep, use for blocking
cleanup e.g. bpf_any_put()
->free_inode() called after RCU grace period, use for freeing
inode and anything RCU-accessible e.g. i_link
Fix: split the two concerns properly:
- keep bpf_any_put() in bpf_destroy_inode() since it is blocking
and needs to run promptly
- introduce bpf_free_inode() to handle kfree(i_link) and
free_inode_nonrcu() with proper RCU delay, preventing the UAF |
| In the Linux kernel, the following vulnerability has been resolved:
nvdimm/btt: Handle preemption in BTT lane acquisition
BTT lanes serialize access to per-lane metadata and workspace state
during BTT I/O. The btt-check unit test reports data mismatches during
BTT writes due to a race in lane acquisition that can lead to silent
data corruption.
The existing lane model uses a spinlock together with a per-CPU
recursion count. That recursion model stopped being valid after BTT
lanes became preemptible: another task can run on the same CPU,
observe a non-zero recursion count, bypass locking, and use the same
lane concurrently.
BTT lanes are also held across arena_write_bytes() calls. That path
reaches nsio_rw_bytes(), which flushes writes with nvdimm_flush().
Some provider flush callbacks can sleep, making a spinlock the wrong
primitive for the lane lifetime.
Replace the spinlock-based recursion model with a dynamically
allocated per-lane mutex array and take the lane lock
unconditionally.
Add might_sleep() to catch any future atomic-context caller.
Found with the ndctl unit test btt-check.sh. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/nldev: Fix locking when accessing mr->pd
Sashiko points out that, due to rereg_mr, the PD is actually variable and
all the touches in nldev are racy.
Use mr->device instead of mr->pd->device.
Getting the PD restrack ID is more tricky. To avoid disturbing all the
happy paths, add an rdma_restrack_sync() operation which is sort of like
flush_workqueue() or synchronize_irq(): after it returns, all the old
nldev touches to the mr are gone and everything sees the new PD. This
makes it safe to reach into the PD pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject sleepable BPF_LSM_CGROUP programs at load time
The cgroup shim runs under rcu_read_lock_dont_migrate(), so we should
not attach any sleepable BPF programs there. Add support to the verifier
to explicitly reject attempts to load sleepable BPF programs destined
for LSM cgroup attachment.
Without this, we get the following splat from a BPF_LSM_CGROUP
program marked BPF_F_SLEEPABLE attached to file_open when it calls
bpf_get_dentry_xattr():
BUG: sleeping function called from invalid context at kernel/locking/rwsem.c:1567
in_atomic(): 0, irqs_disabled(): 0, non_block: 0, pid: 34317, name: load
preempt_count: 0, expected: 0
RCU nest depth: 2, expected: 0
Call Trace:
down_read+0x76/0x480
ext4_xattr_get+0x11f/0x700
__vfs_getxattr+0xf0/0x150
bpf_get_dentry_xattr+0xbb/0xf0
bpf_prog_e76a298dac9218c6_test_open+0x6a/0x85
__cgroup_bpf_run_lsm_current+0x326/0x840
bpf_trampoline_6442534646+0x62/0x14d
security_file_open+0x34/0x60
do_dentry_open+0x340/0x1260
vfs_open+0x7a/0x440
path_openat+0x1bac/0x30a0
libbpf provides a .s named section variant for every sleepable
program type except lsm_cgroup, reflecting that per-cgroup LSM programs
are intended to only run in a non-sleepable context.
The above splat was obtained by bypassing libbpf by using bpf(2)
directly. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Fix TOCTOU heap overflow in get_srq_wqe
get_srq_wqe() reads wqe->dma.num_sge from the shared receive queue
buffer, which is mapped into userspace. It validates num_sge against
max_sge, but then re-reads the same field to calculate the memcpy
size. A concurrent userspace thread can modify num_sge between
validation and use, causing a heap buffer overflow when copying the
WQE into qp->resp.srq_wqe.
Read num_sge into a local variable and use it for both the bounds
check and the size calculation. |
| In the Linux kernel, the following vulnerability has been resolved:
gpu: host1x: Fix iommu_map_sgtable() return value check
Commit "iommu: return full error code from iommu_map_sg[_atomic]()"
changed iommu_map_sgtable() to return an ssize_t and negative values
in error cases, rather than a size_t and a zero.
pin_job() also was incorrectly assigning to 'int', which could cause
overflows into negative values.
Update pin_job() to correctly check for errors from iommu_map_sgtable. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-pci: fix out-of-bounds access in nvme_setup_descriptor_pools
nvme_setup_descriptor_pools() indexes dev->descriptor_pools[] using the
numa_node forwarded from hctx->numa_node by its single caller,
nvme_init_hctx_common(). On a non-NUMA kernel hctx->numa_node is
NUMA_NO_NODE (-1). Because the parameter was declared 'unsigned', the
value becomes UINT_MAX and the index walks off the array (sized to
nr_node_ids), faulting during nvme_alloc_ns() and leaving the namespace
without a /dev node.
Reproduces on any NVMe controller probed by a CONFIG_NUMA=n kernel:
BUG: unable to handle page fault for address: ffff889101603d38
RIP: 0010:nvme_init_hctx_common+0x5a/0x190 [nvme]
Call Trace:
nvme_init_hctx+0x10/0x20 [nvme]
nvme_alloc_ns+0x9e/0xa10 [nvme_core]
nvme_scan_ns+0x301/0x3b0 [nvme_core]
nvme_scan_ns_async+0x23/0x30 [nvme_core]
Switch the parameter to int and fall back to node 0 when it is
NUMA_NO_NODE; node 0 is always present. |
