| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
gpu/buddy: bail out of try_harder when alignment cannot be honoured
The try_harder contiguous fallback could return a range whose start
offset did not match the caller's min_block_size. When a candidate's
start is misaligned, realign it: free the misaligned run and reallocate
exactly @size at the next lower min_block_size boundary. This keeps the
returned size unchanged with no surplus to trim, and rejects the request
only when no aligned candidate fits.
v2: align misaligned candidates down to min_block_size instead of
bailing out, for both the RHS and LHS paths (Matthew). |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: ensure minimal ethernet header on TX
As documented in commit 8bd67ebb50c0 ("net: bridge: xmit: make sure we have
at least eth header len bytes"), it is possible by for a local user with
eBPF TC hook access to attach a tc filter which truncates the packet and
redirects to an batadv interface. But the code assumes that at least
ETH_HLEN bytes are available and thus might read outside of the available
buffer.
The batadv_interface_tx() must therefore always check itself if enough data
is available for the ethernet header and don't rely on min_header_len. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: prevent TVLV OOB check overflow
A TT unicast TVLV contains the number of VLANs stored in it. This number is
an u16 and gets multiplied by the size of the struct
batadv_tvlv_tt_vlan_data (8 bytes). The size can therefore overflow the u16
used to store the tt_vlan_len. All additional safety checks to prevent
out-of-bounds access of the TVLV buffer are invalid due to this overflow.
Using size_t prevents this overflow and ensures that the safety checks
compare against the actual buffer requirements. |
| In the Linux kernel, the following vulnerability has been resolved:
jbd2: fix integer underflow in jbd2_journal_initialize_fast_commit()
jbd2_journal_initialize_fast_commit() validates journal capacity by
checking (journal->j_last - num_fc_blks < JBD2_MIN_JOURNAL_BLOCKS).
Both j_last and num_fc_blks are unsigned, so when num_fc_blks exceeds
j_last the subtraction wraps to a large value, bypassing the bounds
check.
The resulting underflow corrupts j_last, j_fc_first, and j_free,
leading to journal abort.
Fix by checking num_fc_blks against j_last before the subtraction,
returning -EFSCORRUPTED. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: bound attr_off in UpdateResidentValue against data_off
In do_action()'s UpdateResidentValue case (fslog.c:3307),
lrh->attr_off and lrh->redo_len come from the on-disk LRH.
When they satisfy aoff + dlen < attr->res.data_off, the
assignment
attr->res.data_size = cpu_to_le32(aoff + dlen - data_off);
underflows to ~4 GiB (e.g. 0xFFFFFFF9 when aoff=0x10, dlen=1,
data_off=0x18). Subsequent code that reads attr->res.data_size
to walk the resident attribute payload would then read up to
4 GiB past the 1024-byte MFT record allocation.
The existing mi_enum_attr() defense in fs/ntfs3/record.c:287
catches the corrupted data_size on the next attribute walk
and fails the mount, but only on the path that walks all
attributes. A read site that picks an attribute by name and
reads its data_size without re-validating is not covered.
Validate aoff against data_off and asize at the source.
Reproduced under UML+KASAN on mainline 8d90b09e6741 via
pr_warn-only probe: with aoff=0x10 and data_off=0x18, the
post-assignment data_size is 0xfffffff9 (mount then fails
at -22 from mi_enum_attr).
[almaz.alexandrovich@paragon-software.com: clang-formatted the changes] |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs3: bound to_move in indx_insert_into_root before hdr_insert_head
indx_insert_into_root() promotes a full resident $INDEX_ROOT into
$INDEX_ALLOCATION and copies all non-last resident root entries into
a newly allocated INDEX_BUFFER via hdr_insert_head(). The source
byte count 'to_move' is summed from the on-disk resident entry sizes
and is independent of the destination buffer size, which comes from
root->index_block_size (via indx->index_bits).
A crafted NTFS image that keeps a valid, full resident root but
shrinks root->index_block_size down to 512 after the root has been
populated makes hdr_insert_head() memcpy attacker-controlled resident
entry bytes past the end of the kmalloc(1u << indx->index_bits)
allocation returned by indx_new(). For a 512-byte destination and a
resident root whose non-last entries total 560 bytes, the memcpy
overruns by 120 bytes and a following memmove extends the highest
written offset to 136 bytes past the allocation. The overflow bytes
are a direct copy of on-disk entries (via kmemdup), so they are
fully attacker-controlled.
The write is reachable from unprivileged open(O_CREAT) on a mounted
crafted NTFS image: a single sufficiently long create in a directory
whose resident root is already full forces root promotion and
triggers the copy.
This is a controlled out-of-bounds write of 120-136 bytes past a
kmalloc(index_block_size) allocation, with attacker-controlled
content. It is a bounded adjacent-heap corruption primitive; it is
not an arbitrary-address write. Successful exploitation into a named
victim object depends on the surrounding slab layout.
Reject the copy at the sink. The destination's INDEX_HDR already
reports hdr_total (the payload capacity of the new buffer) and
hdr_used (the bytes already consumed by the terminal END entry
installed by indx_new()); require that to_move fits in the remaining
payload before calling hdr_insert_head(). On mismatch, fail with
-EINVAL and mark the filesystem as having a detected on-disk
inconsistency, which is the same behaviour as the surrounding
validation in this function. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: rawnand: fix condition in 'nand_select_target()'
'cs' here must be in range [0:nanddev_ntargets[. |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2: reject dinodes with non-canonical i_mode type
Patch series "ocfs2: harden inode validators against forged metadata", v2.
This series adds three structural checks to OCFS2 dinode validation so
malformed on-disk fields are rejected before ocfs2_populate_inode() copies
them into the in-core inode.
The checks cover:
- i_mode values whose type bits do not name a canonical POSIX file
type;
- non-device dinodes whose id1.dev1.i_rdev field is non-zero; and
- non-inline dinodes that claim non-zero i_size while i_clusters is
zero, covering directories unconditionally and regular files on
non-sparse volumes.
The normal read path reports these through ocfs2_error(), matching the
existing suballoc-slot, inline-data, chain-list, and refcount checks. The
online filecheck path uses the same structural predicates but keeps its
own reporting contract, returning OCFS2_FILECHECK_ERR_INVALIDINO instead
of calling ocfs2_error().
This patch (of 3):
ocfs2_validate_inode_block() currently accepts any non-zero i_mode value.
ocfs2_populate_inode() then copies that mode verbatim into inode->i_mode
and dispatches on i_mode & S_IFMT to the file/dir/symlink/special_file
iops; an unrecognised type falls through to ocfs2_special_file_iops and
init_special_inode().
Reject dinodes whose type bits do not name one of the seven canonical
POSIX file types. Use fs_umode_to_ftype(), the same generic file-type
conversion helper OCFS2 already uses for directory entries, so the
accepted inode type set matches the kernel file-type vocabulary instead of
open-coding a local switch.
Apply the same structural check to the online filecheck read path.
filecheck keeps its own error namespace, so it reports malformed i_mode
through the filecheck logger and OCFS2_FILECHECK_ERR_INVALIDINO instead of
calling ocfs2_error(), but it must not allow a malformed dinode to proceed
into ocfs2_populate_inode(). |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: tegra: Fix burst size calculation
Currently, the Tegra GPC DMA hardware requires the transfer length to
be a multiple of the max burst size configured for the channel. When a
client requests a transfer where the length is not evenly divisible by
the configured max burst size, the DMA hangs with partial burst at
the end.
Fix this by reducing the burst size to the largest power-of-2 value
that evenly divides the transfer length. For example, a 40-byte
transfer with a 16-byte max burst will now use an 8-byte burst
(40 / 8 = 5 complete bursts) instead of causing a hang.
This issue was observed with the PL011 UART driver where TX DMA
transfers of arbitrary lengths were stuck. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: xfrm_interface: require CAP_NET_ADMIN in the device netns for changelink
xfrmi_changelink() operates on at most two netns, dev_net(dev) and the
interface link netns xi->net. They differ once the device is created in
or moved to a netns other than the one the request runs in. The rtnl
changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a
caller privileged there but not in xi->net can rewrite an interface that
lives in xi->net.
Gate xfrmi_changelink() on rtnl_dev_link_net_capable() at its top,
before any attribute is parsed. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet-rdma: handle inline data with a nonzero offset
nvmet_rdma_use_inline_sg() maps the host-controlled inline data offset
into the per-command inline scatterlist. The bounds check admits any
offset with off + len <= inline_data_size, but the mapping still assumes
the data begins in the first inline page:
sg->offset = off;
sg->length = min_t(int, len, PAGE_SIZE - off);
When a port is configured with inline_data_size > PAGE_SIZE (settable up
to max(SZ_16K, PAGE_SIZE)), an offset in (PAGE_SIZE, inline_data_size]
makes "PAGE_SIZE - off" underflow, so sg->length is set to ~4 GiB and
the block backend reads far past the first inline page. num_pages(len)
also ignores the offset, so an in-bounds offset whose [off, off+len)
span crosses a page boundary under-counts the scatterlist.
Map the offset properly: split it into a page index and an in-page
offset, start the scatterlist at that page, and size the page count from
page_off + len. Because the request scatterlist may now start at
inline_sg[page_idx] rather than inline_sg[0], generalize the inline-SGL
identity test in nvmet_rdma_release_rsp() to a range test; otherwise the
persistent inline scatterlist is mistaken for an allocated one and
nvmet_req_free_sgls() frees an inline page (and warns in
free_large_kmalloc()). |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: validate frame length in bcm_rx_setup() for RTR replies
bcm_tx_setup() validates cf->len against the CAN/CAN FD DLC limits
before installing frames for TX_SETUP, but bcm_rx_setup() never did
the same for the RTR-reply frame configured via RX_SETUP with
RX_RTR_FRAME. |
| In the Linux kernel, the following vulnerability has been resolved:
dibs: loopback: validate offset and size in move_data()
The loopback move_data() performs a memcpy into the registered DMB
without checking whether offset + size exceeds the DMB length. Unlike
real ISM hardware, which enforces memory region bounds natively, the
software loopback has no such protection.
A peer-supplied out-of-bounds offset or oversized write would result in
an OOB write past the allocated kernel buffer. Add an explicit bounds
check before the memcpy to reject such requests with -EINVAL. |
| In the Linux kernel, the following vulnerability has been resolved:
net: skbuff: propagate shared-frag marker through frag-transfer helpers
Two frag-transfer helpers (__pskb_copy_fclone() and skb_shift()) fail
to propagate the SKBFL_SHARED_FRAG bit in skb_shinfo()->flags when
moving frags from source to destination. __pskb_copy_fclone() defers
the rest of the shinfo metadata to skb_copy_header() after copying
frag descriptors, but that helper only carries over gso_{size,segs,
type} and never touches skb_shinfo()->flags; skb_shift() moves frag
descriptors directly and leaves flags untouched. As a result, the
destination skb keeps a reference to the same externally-owned or
page-cache-backed pages while reporting skb_has_shared_frag() as
false.
The mismatch is harmful in any in-place writer that uses
skb_has_shared_frag() to decide whether shared pages must be detoured
through skb_cow_data(). ESP input is one such writer (esp4.c,
esp6.c), and a single nft 'dup to <local>' rule -- or any other
nf_dup_ipv4() / xt_TEE caller -- is enough to land a pskb_copy()'d
skb in esp_input() with the marker stripped, letting an unprivileged
user write into the page cache of a root-owned read-only file via
authencesn-ESN stray writes.
Set SKBFL_SHARED_FRAG on the destination whenever frag descriptors
were actually moved from the source. skb_copy() and skb_copy_expand()
share skb_copy_header() too but linearize all paged data into freshly
allocated head storage and emerge with nr_frags == 0, so
skb_has_shared_frag() returns false on its own; they need no change.
The same omission exists in skb_gro_receive() and skb_gro_receive_list().
The former moves the incoming skb's frag descriptors into the
accumulator's last sub-skb via two paths (a direct frag-move loop and
the head_frag + memcpy path); the latter chains the incoming skb whole
onto p's frag_list. Downstream skb_segment() reads only
skb_shinfo(p)->flags, and skb_segment_list() reuses each sub-skb's
shinfo as the nskb -- both p and lp must carry the marker.
The same omission also exists in tcp_clone_payload(), which builds an
MTU probe skb by moving frag descriptors from skbs on sk_write_queue
into a freshly allocated nskb. The helper falls into the same family
and warrants the same fix for consistency; no TCP TX-side in-place
writer is currently known to reach a user page through this gap, but
a future consumer depending on the marker would regress silently.
The same omission exists in skb_segment(): the per-iteration flag
merge takes only head_skb's flag, and the inner switch that rebinds
frag_skb to list_skb on head_skb-frags exhaustion does not fold the
new frag_skb's flag into nskb. Fold frag_skb's flag at both sites
so segments drawing frags from frag_list members carry the marker. |
| Out-of-bounds read in DNS Server allows an authorized attacker to disclose information over a network. |
| Out-of-bounds read in DNS Server allows an authorized attacker to disclose information over a network. |
| Out-of-bounds read in Microsoft Graphics Component allows an authorized attacker to elevate privileges locally. |
| Heap-based buffer overflow in Windows Overlay Filter allows an unauthorized attacker to execute code with a physical attack. |
| Heap-based buffer overflow in Microsoft Office Excel allows an unauthorized attacker to execute code over a network. |
| Progress MarkLogic Server 12.x releases before 12.1.0 and 11.x releases before 11.3.7 do not sufficiently sanitize input used by the Query Console file-exploration endpoint, which could allow HTTP response splitting and unintended client-side response handling. |
