Export limit exceeded: 390737 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (23516 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-63943 | 1 Linux | 1 Linux Kernel | 2026-08-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: Input: xpad - fix out-of-bounds access for Share button xpadone_process_packet() receives len directly from urb->actual_length and uses it to index the share-button byte at data[len - 18] or data[len - 26]. Since both len and data[0] are under the device's control, a broken controller can send a GIP_CMD_INPUT packet with actual_length < 18 (e.g. 5 bytes) and reach this code path, causing accesses beyond the actual array. Fix this by calculating the offset and checking bounds against the packet length. | ||||
| CVE-2026-16422 | 2 Google, Linux | 2 Chrome, Linux Kernel | 2026-08-04 | 7.5 High |
| Insufficient validation of untrusted input in Certificate in Google Chrome on Linux prior to 150.0.7871.182 allowed an attacker in a privileged network position to perform domain spoofing via malicious network traffic. (Chromium security severity: High) | ||||
| CVE-2026-64275 | 1 Linux | 1 Linux Kernel | 2026-08-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: Input: elan_i2c - prevent division by zero and arithmetic underflow The Elan I2C touchpad driver queries the device for its physical dimensions and trace counts to calculate the device resolution and width. However, if the device firmware or device tree provides invalid zero values for x_traces or y_traces, it results in a fatal division-by-zero exception leading to a kernel panic during device probe. Add checks to ensure these parameters are non-zero before performing the division. If invalid trace values are detected, fall back to a safe default of 1. Additionally, prevent an arithmetic underflow in the touch reporting logic. Previously, if the calculated or fallback width was smaller than ETP_FWIDTH_REDUCE (90), the subtraction would underflow, resulting in a massive unsigned integer being reported to userspace. Clamp the adjusted width to a minimum of 0 to safely handle small physical dimensions and fallback scenarios. Completing the probe with safe fallback values ensures the sysfs nodes are created, keeping the firmware update path intact so a recovery firmware can be flashed to the device. | ||||
| CVE-2026-64277 | 1 Linux | 1 Linux Kernel | 2026-08-03 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: Input: synaptics-rmi4 - bound the F3A keymap to the GPIO count rmi_f3a_initialize() takes the GPIO count from the device query register (f3a->gpio_count = buf & RMI_F3A_GPIO_COUNT, range 0..127). rmi_f3a_map_gpios() then allocates gpio_key_map with min(gpio_count, TRACKSTICK_RANGE_END) == at most 6 entries, but rmi_f3a_attention() iterates the full gpio_count and dereferences gpio_key_map[i], and input->keycodemax is set to the full gpio_count while input->keycode points at the 6-entry allocation. A device that reports gpio_count > 6 therefore causes an out-of-bounds read of gpio_key_map[] on every attention interrupt, and out-of-bounds accesses through the input core's default keymap ioctls: EVIOCGKEYCODE reads past the buffer (leaking adjacent slab memory to user space) and EVIOCSKEYCODE writes a caller-controlled value past it, for any process able to open the evdev node, since input_default_getkeycode() and input_default_setkeycode() only bound the index against keycodemax. Size the keymap for the full gpio_count. The mapping loop is unchanged: it still assigns only the first min(gpio_count, TRACKSTICK_RANGE_END) entries; the remaining slots stay KEY_RESERVED (devm_kcalloc zero-fills) and are skipped when reporting. | ||||
| CVE-2026-64284 | 1 Linux | 1 Linux Kernel | 2026-08-03 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Ensure vendor's exit handler runs before fastpath userspace exits Move the handling of fastpath userspace exits into vendor code to ensure KVM runs vendor specific operations that need to run before userspace gains control of the vCPU. E.g. for VMX (and soon to be for SVM as well), KVM needs to flush the PML buffer prior to exiting to userspace, otherwise any memory written by the final KVM_RUN might never be flagged as dirty. Note, waiting to snapshot CR0 and CR3 until svm_handle_exit() is flawed in general, as that risks consuming stale state in a fastpath handler. That will be addressed in a future change. | ||||
| CVE-2026-64290 | 1 Linux | 1 Linux Kernel | 2026-08-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: iommufd: Break the loop on failure in iommufd_fault_fops_read() On a copy_to_user() failure inside the inner list_for_each_entry, only the inner loop breaks; the outer while re-fetches the just-restored fault group and retries the failing copy_to_user() forever, spinning the reader at 100% CPU with fault->mutex held. Check rc after the inner loop and break the outer while as well. | ||||
| CVE-2026-64360 | 1 Linux | 1 Linux Kernel | 2026-08-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: hfs/hfsplus: zero-initialize buffer in hfs_bnode_read hfs_bnode_read() can return early without writing to the output buffer when is_bnode_offset_valid() fails or when check_and_correct_requested_ length() corrects the length to zero. Callers such as hfs_bnode_read_ u16() and hfs_bnode_read_u8() pass stack-allocated buffers and use the result unconditionally, leading to KMSAN uninit-value reports. Rather than initializing at each individual call site, zero the buffer at the start of hfs_bnode_read() before any validation checks. This ensures all callers in both hfs and hfsplus get a deterministic zero value regardless of which early-return path is taken. | ||||
| CVE-2026-64409 | 1 Linux | 1 Linux Kernel | 2026-08-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btmtksdio: fix infinite loop in btmtksdio_txrx_work() Every once in a while we see a hung btmtksdio_flush() task: INFO: task kworker/u17:0:189 blocked for more than 122 seconds. __cancel_work_timer+0x3f4/0x460 cancel_work_sync+0x1c/0x2c btmtksdio_flush+0x2c/0x40 hci_dev_open_sync+0x10c4/0x2190 [..] It all boils down to incorrect time_is_before_jiffies() usage in btmtksdio_txrx_work(). The btmtksdio_txrx_work() loop is expected to be terminated if running for longer than 5*HZ. However the timeout check is twisted: time_is_before_jiffies(old_jiffies + 5*HZ) evaluates to true when old_jiffies + 5*HZ is in the past i.e. when a timeout has occurred. Using OR with time_is_before_jiffies(txrx_timeout) means that: - before the 5-second timeout: the condition is `int_status || false`, so it loops as long as there are pending interrupts. - after the 5-second timeout: the condition becomes `int_status || true`, which is always true. When the loop becomes infinite btmtksdio_txrx_work() loop never terminates and never releases the SDIO host. Fix loop termination condition to actually enforce a 5*HZ timeout. | ||||
| CVE-2026-64457 | 1 Linux | 1 Linux Kernel | 2026-08-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: virtio_pci: fix vq info pointer lookup via wrong index Unbinding a virtio balloon device: echo virtio0 > /sys/bus/virtio/drivers/virtio_balloon/unbind triggers a NULL pointer dereference. The dmesg says: BUG: kernel NULL pointer dereference, address: 0000000000000008 [...] RIP: 0010:__list_del_entry_valid_or_report+0x5/0xf0 Call Trace: <TASK> vp_del_vqs+0x121/0x230 remove_common+0x135/0x150 virtballoon_remove+0xee/0x100 virtio_dev_remove+0x3b/0x80 device_release_driver_internal+0x187/0x2c0 unbind_store+0xb9/0xe0 kernfs_fop_write_iter.llvm.11660790530567441834+0xf6/0x180 vfs_write+0x2a9/0x3b0 ksys_write+0x5c/0xd0 do_syscall_64+0x54/0x230 entry_SYSCALL_64_after_hwframe+0x29/0x31 [...] </TASK> The virtio_balloon device registers 5 queues (inflate, deflate, stats, free_page, reporting) but only the first two are unconditional. The stats, free_page and reporting queues are each conditional on their respective feature bits. When any of these features are absent, the corresponding vqs_info entry has name == NULL, creating holes in the array. The root cause is an indexing mismatch introduced when vq info storage was changed to be passed as an argument. vp_find_vqs_msix() and vp_find_vqs_intx() store the info pointer at vp_dev->vqs[i], where 'i' is the caller's sparse array index. However, the virtqueue itself gets vq->index assigned from queue_idx, a dense index that skips NULL entries. When holes exist, 'i' and queue_idx diverge. Later, vp_del_vqs() looks up info via vp_dev->vqs[vq->index] using the dense index into the sparsely-populated array, and hits NULL. Fix this by storing info at vp_dev->vqs[queue_idx] instead of vp_dev->vqs[i], so the store index matches the lookup index (vq->index). Apply the fix to both the MSIX and INTX paths. | ||||
| CVE-2026-64470 | 1 Linux | 1 Linux Kernel | 2026-08-03 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btusb: fix use-after-free on marvell probe failure Make sure to stop any TX URBs submitted during Marvell OOB wakeup configuration on later probe failures to avoid use-after-free in the completion callback. This issue was reported by Sashiko while reviewing a fix for a wakeup source leak in the btusb probe errors paths. | ||||
| CVE-2026-64475 | 1 Linux | 1 Linux Kernel | 2026-08-03 | 8.8 High |
| In the Linux kernel, the following vulnerability has been resolved: vfio/pci: Release the VGA arbiter client on register_device() failure The re-order in the Fixes commit below displaced vfio_pci_vga_init() as the last failure point of what is now vfio_pci_core_register_device() without introducing an unwind for the VGA arbiter registration. In current kernels this is mostly benign because vfio_pci_set_decode() only uses pci_dev state, but the original failure path could leave a callback with a freed vdev cookie. The stale registration also becomes unsafe again once the callback follows drvdata to the vfio device. Add the required VGA unwind callout. | ||||
| CVE-2026-64500 | 1 Linux | 1 Linux Kernel | 2026-08-03 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: iio: adc: lpc32xx: Initialize completion before requesting IRQ In the report from Jaeyoung Chung: "lpc32xx_adc_probe() in drivers/iio/adc/lpc32xx_adc.c registers its interrupt handler with devm_request_irq() before it initializes st->completion with init_completion(). If an interrupt arrives after devm_request_irq() and before init_completion(), the handler calls complete() on an uninitialized completion, causing a kernel panic. The probe path, in lpc32xx_adc_probe(): iodev = devm_iio_device_alloc(&pdev->dev, sizeof(*st)); /* st kzalloc-zeroed */ ... retval = devm_request_irq(&pdev->dev, irq, lpc32xx_adc_isr, 0, LPC32XXAD_NAME, st); /* register handler */ ... init_completion(&st->completion); /* initialize completion */ lpc32xx_adc_isr() calls complete(): complete(&st->completion); If the device raises an interrupt before init_completion() runs, complete() acquires the uninitialized wait.lock and walks the zeroed task_list in swake_up_locked(). The zeroed task_list makes list_empty() return false, so swake_up_locked() dereferences a NULL list entry, triggering a KASAN wild-memory-access." Fix the chance of a spurious IRQ causing an uninitialized pointer dereference by moving init_completion() above devm_request_irq(). | ||||
| CVE-2026-64505 | 1 Linux | 1 Linux Kernel | 2026-08-03 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: usb: gadget: function: rndis: add length check for header Add a length check for the rndis header in rndis_rm_hdr, to ensure that MessageType, MessageLength, DataOffset, and DataLength fields are present before they are accessed. | ||||
| CVE-2026-64506 | 1 Linux | 1 Linux Kernel | 2026-08-03 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: wifi: rtw89: correct drop logic for malformed AMPDU frames The previous commit aims to fix issue caused by malformed AMPDU frames. But the drop logic fails to deal with the first AMPDU packet paired with certain range of sequence number, and leads to unexpected packet drop. It is more likely to encounter this failure when there are busy traffic during rekey process and could lead to disconnection from the AP. Fix this by adding a initial state judgement and only reset status during pairwise rekey. | ||||
| CVE-2026-64515 | 1 Linux | 1 Linux Kernel | 2026-08-03 | 8.3 High |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: fix MLE defragmentation If either reconf or EPCS multi-link element (MLE) is contained in a non-transmitted profile, the defragmentation routine is called with a pointer to the defragmented copy, but the original elements. This is incorrect for two reasons: - if the original defragmentation was needed, it will not find the correct data - if the original frame is at a higher address, the parsing will potentially overrun the heap data (though given the layout of the buffers, only into the new defragmentation buffer, and then it has to stop and fail once that's filled with copied data. Fix it by tracking the container along with the pointer and in doing so also unify the two almost identical defragmentation routines. | ||||
| CVE-2026-64519 | 1 Linux | 1 Linux Kernel | 2026-08-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: NFSD: Fix infinite loop in layout state revocation find_one_sb_stid() skips stids whose sc_status is non-zero, but the SC_TYPE_LAYOUT case in nfsd4_revoke_states() never sets sc_status before calling nfsd4_close_layout(). The retry loop therefore finds the same layout stid on every iteration, hanging the revoker indefinitely. | ||||
| CVE-2026-64522 | 1 Linux | 1 Linux Kernel | 2026-08-03 | 8.8 High |
| In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix eswitch mode block underflow on IPsec acquire SA mlx5e_xfrm_add_state() handles acquire-flow temporary SAs by allocating software state and skipping hardware offload setup. That path jumps to the common success label before taking the eswitch mode block. After tunnel-mode validation was moved earlier, the common success label unconditionally calls mlx5_eswitch_unblock_mode(). For acquire SAs, this decrements esw->offloads.num_block_mode without a matching increment. Return directly after installing the acquire SA offload handle, so only the paths that successfully called mlx5_eswitch_block_mode() call the matching unblock. | ||||
| CVE-2026-64525 | 1 Linux | 1 Linux Kernel | 2026-08-03 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: xfrm: move policy_bydst RCU sync from per-netns .exit to .pre_exit The struct pernet_operations docstring in include/net/net_namespace.h explicitly warns against blocking RCU primitives in .exit handlers: Exit methods using blocking RCU primitives, such as synchronize_rcu(), should be implemented via exit_batch. [...] Please, avoid synchronize_rcu() at all, where it's possible. Note that a combination of pre_exit() and exit() can be used, since a synchronize_rcu() is guaranteed between the calls. xfrm_policy_fini() violates this: it calls synchronize_rcu() before freeing the policy_bydst hash tables (so no RCU reader is mid- traversal at free time), but runs from xfrm_net_ops.exit -- once per namespace -- so a cleanup_net() of N namespaces pays N full RCU grace periods serially. Use the documented pre_exit/exit split. Move the policy flush (and the workqueue drains it depends on) into a new .pre_exit handler; xfrm_policy_fini() then runs in .exit and frees the hash tables after the synchronize_rcu_expedited() that cleanup_net() guarantees between the two phases. Providing O(1) RCU grace periods per batch instead of O(N). Observed on Linux 6.18 with a workload doing unshare(CLONE_NEWNET) at ~13/sec sustained: cleanup_net() and the netns_wq rescuer kthread both stuck in xfrm_policy_fini()'s synchronize_rcu(), >300k struct net accumulated in the cleanup queue, Percpu in /proc/meminfo climbed to 130+ GB on 256-CPU hosts, and memcg OOMs followed. setup_net and __put_net counts were balanced, ruling out a refcount leak. | ||||
| CVE-2026-64536 | 1 Linux | 1 Linux Kernel | 2026-08-03 | 8.1 High |
| In the Linux kernel, the following vulnerability has been resolved: staging: rtl8723bs: fix OOB reads in is_ap_in_tkip() IE loop The loop in is_ap_in_tkip() iterates over IEs without verifying that enough bytes remain before dereferencing the IE header or its payload: - pIE->element_id and pIE->length are read without checking that i + sizeof(*pIE) <= ie_length, so a truncated IE at the end of the buffer causes an OOB read. - For WLAN_EID_VENDOR_SPECIFIC the code compares pIE->data + 12, which requires pIE->length >= 16. For WLAN_EID_RSN it compares pIE->data + 8, requiring pIE->length >= 12. Neither requirement is checked. Add the missing IE header and payload bounds checks and guard each data access with an explicit pIE->length minimum, matching the pattern established in update_beacon_info(). | ||||
| CVE-2022-4994 | 1 Linux | 1 Linux Kernel | 2026-08-03 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: KVM: x86: wean fast IN from emulator_pio_in Use __emulator_pio_in() directly for fast PIO instead of bouncing through emulator_pio_in() now that __emulator_pio_in() fills "val" when handling in-kernel PIO. vcpu->arch.pio.count is guaranteed to be '0', so this a pure nop. emulator_pio_in_emulated is now the last caller of emulator_pio_in. No functional change intended. | ||||