| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: SDCA: Validate written enum value in ge_put_enum_double()
ge_put_enum_double() passes the user-supplied enumeration index
item[0] to snd_soc_enum_item_to_val() without checking it against the
number of items in the enum:
ret = snd_soc_enum_item_to_val(e, item[0]);
snd_soc_enum_item_to_val() indexes the heap-allocated e->values[] array
with that index (e->values is set from a devm_kcalloc() of e->items
entries), so a control write with an out-of-range item[0] reads past the
end of the values buffer. The bounds check in
snd_soc_dapm_put_enum_double() only runs afterwards, so it does not
prevent the read here.
Reject an out-of-range item before using it, matching the other enum put
handlers.
This issue was pointed out by the Sashiko AI review bot while reviewing a
related enum-validation series:
https://lore.kernel.org/all/20260609125735.CEB651F00893@smtp.kernel.org/ |
| In the Linux kernel, the following vulnerability has been resolved:
net: enetc: check the number of BDs needed for xdp_frame
The size of xdp_redirect_arr array is ENETC_MAX_SKB_FRAGS. However, the
number of fragments contained in xdp_frame may be greater than or equal
to ENETC_MAX_SKB_FRAGS, which will cause the access to xdp_redirect_arr
to be out of bounds. |
| The Zephyr ADIN2111/ADIN1110 10BASE-T1S/T1L Ethernet driver (drivers/ethernet/eth_adin2111.c) reassembles received Ethernet frames in OPEN Alliance (OA) SPI mode by copying device-supplied 64-byte data chunks into a fixed static buffer ctx->buf of size CONFIG_ETH_ADIN2111_BUFFER_SIZE (default 1524 bytes). In eth_adin2111_oa_data_read(), each valid chunk was memcpy'd into ctx->buf[ctx->scur] and the write cursor scur advanced, with no check that scur + len stayed within the buffer. The number of chunks (up to 255, from the BUFSTS RCA field) and the per-chunk length are taken entirely from the frame data received off the wire; the cursor is only reset on a start-of-frame chunk. An attacker on the single-pair Ethernet segment can therefore send a frame whose reassembled size exceeds the configured buffer, causing the driver's RX offload thread to write attacker-controlled frame bytes past the end of the static buffer into adjacent driver/kernel memory (up to roughly 14.8 KB in the worst case). This is a remotely/adjacently reachable out-of-bounds write (CWE-787) that can corrupt memory and cause denial of service or potentially code execution. The defect was introduced when OA SPI support was added (commit 0ca8b0756b1) and shipped in releases v3.7.0 through v4.4.0. The fix adds a bounds check that drops the oversized frame and resets the cursor before the copy. |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: validate DFS referral string offsets
parse_dfs_referrals() validates that the response header and referral
array fit in the received buffer, but each referral also contains string
offsets supplied by the server.
Those offsets are used to compute the DfsPath and NetworkAddress string
pointers without checking whether they still point inside the response
buffer. A malformed referral can therefore make the computed pointer
exceed the end of the buffer. The resulting negative max_len is then
passed to cifs_strndup_from_utf16(), and the non-Unicode path forwards it
to kstrndup() as a size_t, allowing strnlen() to read out of bounds.
Validate each string offset before deriving the string pointer. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to obtain sensitive information due to an out-of-bounds read. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote authenticated attacker to obtain sensitive information due to an out-of-bounds read. |
| In the Linux kernel, the following vulnerability has been resolved:
gue: validate REMCSUM private option length
GUE private flags can indicate that remote checksum offload metadata is
present. The private flags field itself is accounted for by
guehdr_flags_len(), but guehdr_priv_flags_len() currently returns 0 even
when GUE_PFLAG_REMCSUM is set.
This lets a packet with only the private flags field pass
validate_gue_flags(), after which gue_remcsum() and gue_gro_remcsum()
read the missing REMCSUM start/offset fields from the following bytes.
Account for GUE_PLEN_REMCSUM when GUE_PFLAG_REMCSUM is present so that
malformed packets are rejected during option validation. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: flowtable: fix and simplify IP6IP6 tunnel handling
Fix nf_flow_ip6_tunnel_proto() to use pskb_may_pull() instead of
skb_header_pointer() to ensure the outer IPv6 header is in the skb
headroom, which is required for subsequent packet processing. Move
ctx->offset update inside the IPPROTO_IPV6 conditional block since it
should only be adjusted when an IP6IP6 tunnel is actually detected.
Simplify the rx path by removing ipv6_skip_exthdr() and checking
ip6h->nexthdr directly, as the flowtable fast path only handles simple
IP6IP6 encapsulation without extension headers.
Drop the tunnel encapsulation limit destination option support from the
tx path to match, since the rx path no longer handles extension headers.
Remove the encap_limit parameter from nf_flow_offload_ipv6_forward(),
nf_flow_tunnel_ip6ip6_push() and nf_flow_tunnel_v6_push(), along with
the ipv6_tel_txoption struct and related headroom/MTU adjustments. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: fsl: fsl_audmix: Validate written enum values
fsl_audmix_put_mix_clk_src() and fsl_audmix_put_out_src()
convert the user-provided enum item with snd_soc_enum_item_to_val()
before checking whether the item is within the enum's item count.
The generic snd_soc_put_enum_double() helper performs that
validation, but these callbacks use the converted value first: the
clock-source path tests it with BIT(), and the output-source path
indexes the prms transition table with it.
Reject out-of-range enum items before converting them. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to cause a denial of service and obtain sensitive information due to an integer underflow. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_nat: avoid invalid nat_net pointer use on failed nf_nat_init()
We ran into below KASAN splat, which is mostly uninteresting, beside
for having nf_nat_register_fn() in the call chain as a cause for the
offending access:
==================================================================
BUG: KASAN: slab-out-of-bounds in nf_nat_register_fn+0x5f9/0x640
Read of size 8 at addr ffff890031e54c20 by task iptables/9510
CPU: 0 UID: 0 PID: 9510 Comm: iptables Not tainted 6.18.18-grsec-full-20260320181326 #1 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
Call Trace:
<TASK>
[…] dump_stack_lvl+0xee/0x160 ffff88004117eeb8
[…] print_report+0x6e/0x640 ffff88004117eee0
[…] ? __phys_addr+0x8e/0x140 ffff88004117eef0
[…] ? kasan_addr_to_slab+0x51/0xe0 ffff88004117ef08
[…] ? complete_report_info+0xec/0x1c0 ffff88004117ef20
[…] ? nf_nat_register_fn+0x5f9/0x640 ffff88004117ef48
[…] kasan_report+0xbc/0x140 ffff88004117ef50
[…] ? nf_nat_register_fn+0x5f9/0x640 ffff88004117ef90
[…] nf_nat_register_fn+0x5f9/0x640 ffff88004117eff8
[…] ? nf_nat_icmp_reply_translation+0x6e0/0x6e0 ffff88004117f070
[…] nf_tables_register_hook.part.0+0xa0/0x220 ffff88004117f080
[…] nf_tables_addchain.constprop.0+0x1054/0x1fc0 ffff88004117f0b8
[…] ? nft_chain_lookup.part.0+0x4ce/0xac0 ffff88004117f130
[…] ? nf_tables_abort+0x3d80/0x3d80 ffff88004117f190
[…] ? nf_tables_dumpreset_obj+0x100/0x100 ffff88004117f1c8
[…] ? nft_table_lookup.part.0+0x255/0x300 ffff88004117f310
[…] ? nf_tables_newchain+0x21a4/0x2fa0 ffff88004117f358
[…] nf_tables_newchain+0x21a4/0x2fa0 ffff88004117f360
[…] ? nf_tables_addchain.constprop.0+0x1fc0/0x1fc0 ffff88004117f458
[…] ? nla_get_range_signed+0x4a0/0x4a0 ffff88004117f488
[…] ? lock_acquire+0x16f/0x320 ffff88004117f490
[…] ? find_held_lock+0x3b/0xe0 ffff88004117f4b0
[…] ? __nla_parse+0x45/0x80 ffff88004117f500
[…] nfnetlink_rcv_batch+0xbca/0x19a0 ffff88004117f550
[…] ? nfnetlink_net_exit_batch+0x120/0x120 ffff88004117f618
[…] ? __sanitizer_cov_trace_switch+0x63/0xe0 ffff88004117f720
[…] ? gr_acl_handle_mmap+0x1c4/0x320 ffff88004117f7c0
[…] ? nla_get_range_signed+0x4a0/0x4a0 ffff88004117f7e8
[…] ? gr_is_capable+0x6f/0xe0 ffff88004117f830
[…] ? __nla_parse+0x45/0x80 ffff88004117f860
[…] ? skb_pull+0x103/0x1a0 ffff88004117f880
[…] nfnetlink_rcv+0x3db/0x4a0 ffff88004117f8b0
[…] ? nfnetlink_rcv_batch+0x19a0/0x19a0 ffff88004117f8d8
[…] ? netlink_lookup+0xe2/0x240 ffff88004117f900
[…] netlink_unicast+0x74b/0xb00 ffff88004117f930
[…] ? netlink_attachskb+0xb20/0xb20 ffff88004117f980
[…] ? __check_object_size+0x3e/0xaa0 ffff88004117f998
[…] ? security_netlink_send+0x51/0x160 ffff88004117f9c8
[…] netlink_sendmsg+0xa03/0x1200 ffff88004117f9f8
[…] ? netlink_unicast+0xb00/0xb00 ffff88004117fa70
[…] ? netlink_unicast+0xb00/0xb00 ffff88004117fac8
[…] ? ____sys_sendmsg+0xe2a/0x1040 ffff88004117faf8
[…] ____sys_sendmsg+0xe2a/0x1040 ffff88004117fb00
[…] ? kernel_recvmsg+0x300/0x300 ffff88004117fb60
[…] ? reacquire_held_locks+0xe9/0x260 ffff88004117fbc8
[…] ___sys_sendmsg+0x138/0x200 ffff88004117fbf8
[…] ? do_recvmmsg+0x7e0/0x7e0 ffff88004117fc30
[…] ? lockdep_hardirqs_on_prepare+0x101/0x1e0 ffff88004117fc50
[…] ? lock_acquire+0x16f/0x320 ffff88004117fd20
[…] ? lock_acquire+0x16f/0x320 ffff88004117fd58
[…] ? find_held_lock+0x3b/0xe0 ffff88004117fd70
[…] __sys_sendmsg+0x17a/0x260 ffff88004117fdc8
[…] ? __sys_sendmsg_sock+0x80/0x80 ffff88004117fdf0
[…] ? syscall_trace_enter+0x15e/0x2c0 ffff88004117fe98
[…] do_syscall_64+0x7d/0x400 ffff88004117fec8
[…] entry_SYSCALL_64_safe_stack+0x4a/0x60 ffff88004117fef8
</TASK>
==================================================================
The out-of-bounds report, though, is a red herring as it is f
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: Check ROM header and data structure addr before accessing
We meet a crash when running stress-ng on x86_64 machine:
BUG: unable to handle page fault for address: ffa0000007f40000
RIP: 0010:pci_get_rom_size+0x52/0x220
Call Trace:
<TASK>
pci_map_rom+0x80/0x130
pci_read_rom+0x4b/0xe0
kernfs_file_read_iter+0x96/0x180
vfs_read+0x1b1/0x300
Our analysis reveals that the ROM space's start address is
0xffa0000007f30000, and size is 0x10000. Because of broken ROM space,
before calling readl(pds), the pds's value is 0xffa0000007f3ffff, which is
already pointed to the ROM space end, invoking readl() would read 4 bytes
therefore cause an out-of-bounds access and trigger a crash. Fix this by
adding image header and data structure checking.
We also found another crash on arm64 machine:
Unable to handle kernel paging request at virtual address ffff8000dd1393ff
Mem abort info:
ESR = 0x0000000096000021
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x21: alignment fault
The call trace is the same with x86_64, but the crash reason is that the
data structure addr is not aligned with 4, and arm64 machine report
"alignment fault". Fix this by adding alignment checking.
[bhelgaas: shorten function names, wrap comments] |
| In PHP versions 7.2.x below 7.2.26, 7.3.x below 7.3.13 and 7.4.0, PHP bcmath extension functions on some systems, including Windows, can be tricked into reading beyond the allocated space by supplying it with string containing characters that are identified as numeric by the OS but aren't ASCII numbers. This can read to disclosure of the content of some memory locations. |
| When PHP EXIF extension is parsing EXIF information from an image, e.g. via exif_read_data() function, in PHP versions 7.2.x below 7.2.26, 7.3.x below 7.3.13 and 7.4.0 it is possible to supply it with data what will cause it to read past the allocated buffer. This may lead to information disclosure or crash. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Copy WQE to local buffer in non-SRQ receive path
For non-SRQ QPs, the responder reads WQE fields directly from the
shared queue buffer mapped into userspace. This allows a malicious
user to modify fields like num_sge or sge entries while the kernel
is processing the WQE, leading to out-of-bounds reads in
rxe_resp_check_length() and copy_data().
Introduce get_recv_wqe() that validates num_sge and copies the WQE
to a kernel-local buffer before processing, matching the approach
already used for SRQ WQEs in get_srq_wqe(). The srq_wqe buffer is
reused since SRQ and non-SRQ paths are mutually exclusive per QP. |
| Red Hat CNA-LR concluded that this CVE is not valid. |
| A maliciously crafted DWG or DXF file, when parsed through Autodesk AutoCAD, can force an Out-of-Bounds Read vulnerability. A malicious actor can leverage this vulnerability to cause a crash or disclose sensitive information. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: amd: acp-sdw-legacy: Bound DAI link iteration
create_sdw_dailinks() walks soc_dais until it finds an entry with
initialised cleared, but soc_dais is allocated with exactly num_ends
entries. If all entries are initialised, the loop reads past the end of
the array.
This was reported by KASAN:
BUG: KASAN: slab-out-of-bounds in mc_probe+0x26b3/0x2774 [snd_acp_sdw_legacy_mach]
Read of size 1
Pass the allocated entry count to create_sdw_dailinks() and stop before
reading past the array. |
| A flaw was found in SSSD. The extract_authtok_v1() function in the PAM responder does not validate the auth_token_length field against the remaining buffer size before processing. A local attacker can exploit this via a crafted protocol v1 request to the PAM responder socket, causing an out-of-bounds read and process crash, resulting in a denial of service. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: amd: acp-sdw-sof: Bound DAI link iteration
create_sdw_dailinks() walks sof_dais until it finds an entry with
initialised cleared, but sof_dais is allocated with exactly num_ends
entries. If all entries are initialised, the loop reads past the end of
the array.
Pass the allocated entry count to create_sdw_dailinks() and stop before
reading past the array. |
